Setting
Setting
System Settings
•
Resolution:
Setting video resolution of footage recorded,
Front camera only:
1920*1080P 60FPS, 1920*1080P 30FPS
Front + Rear Camera: 1920*1080P 30FPS
•
Bitrate:
You can set the bitrate for video. High bitrate may improve
the quality and smoothness of the video, especially when recording
fast motion or high contrast scenes. Using high bitrate mode may
decrease the amount of recording time available on your memory
card. Using low bitrate will save space and record for longer time.
•
Live Video Source:
Front camera / Rear camera / PIP mode 1 / PIP
mode 2.
•
Loop Recording:
Off / 1 / 2 / 3 / 5 / 10 minutes.
Recording will begin automatically after powering on with a micro
SD card in the device. Each recorded file is up to three minutes long,
with old footage being replaced when micro SD card storage is full.
•
WDR (Wide Dynamic Range):
Dynamic range is the ratio of the
brightest portion of the image to the darkest portion of the image.
WDR enables the camera to deliver video with near perfect exposure
in varying lighting situations.
•
Exposure:
Adjusting the value of the EV (Exposure Value) properly
can create better footage under different light sources. It ranges from
-2.0 to +2.0. You can adjust the EV for front and rear camera
separately. Default is set at 0.0.
•
Parking Mode:
To use the parking mode, it requires the camera to
connect to the vehicle via the hardwiring cable (optional). The
hardwiring cable must be professionally installed to the vehicle by a
trained mechanic. Your vehicle is under the protection at all times with
parking mode recording that is triggered by motion and impact
detection.
•
Time-lapse Recording:
Record video from frames captured at
specific time intervals to conserve memory and reduce the time it
takes to review video. The default is off.
•
Motion Detection:
When activated, the camera will start recording if
there is movement in front of the camera. Once the camera does not
detect movement for 60 seconds, it stops recording and returns to
“Motion Detection” mode. The camera will record again in the time of
detecting a new movement.
•
GPS:
Turn on / off GPS logger. A GPS module is used to include the
location data in the recorded videos. If disabled, your camera will no
longer measure your speed and position; nor synchronize the time /
date. (Only available when connect with GPS signal) Please use
“Dashcam Viewer” to playback videos and to visualize your position
and speed on your computer.
•
Speed Unit:
Kilometer per hour (KMH) and miles per hour (MPH) are
available for speed unit.
•
G-Sensor:
The G-sensor measures shock forces and locks the video
recorded at the time. The settings from “low to high” determine the
amount of force needed to lock the file from being overwritten. We
recommend that you set it at low.
19
20
•
Wi-Fi:
Set it On / Off. Press the [ ] button for 3 or 5 seconds to
enable Wi-Fi quickly.
•
Bluetooth Remote:
Set it On / Off.
•
Date Stamp:
Imprint the time and date on the recorded video.
•
GPS Info Stamp:
Imprint the GPS information on the recorded video
.
•
Camera Model Stamp:
Imprint the camera model on the recorded
video.
•
Record Audio:
Turn on and off the microphone. This can also be
changed during recording by pressing the microphone button [ ].
•
Screen Saver:
The screen goes black by default after 3 minutes while
recording. You can set it by adjusting different time intervals on menu.
•
Date / Time:
Set system date / time.
•
Time Zone:
Set the current time zone for GPS time and date
calibration.
Note: the time zone must be manually adjusted for daylight savings.
•
Language:
Set the on-screen display to English, Traditional Chinese,
and French, etc.
•
Beep Sound:
Turn all notification sounds On / Off.
•
Frequency:
Set it to minimize flickering and banding in the recorded
video.
•
Image Rotation:
Turn the screen upside down. It’s fit for both front
and rear camera.
•
Format:
The operation will delete all data on the Micro SD card.
Note: Once you format the card, all information will be deleted and
unrecoverable. Make sure to back up all files that you needed before
formatting.
•
Format Warning:
Set the number of days between format warnings.
•
Default Setting:
Restore device to factory settings.
•
Car Number:
Imprint the car number on the recorded video.
•
Custom Text Stamp:
Imprint the customize text on the recorded
video.
•
Firmware Version:
Check the current firmware version of the
camera.
