Vinten Vision 250 IT Maintenance Manual Download

Page: 18 / 71

Connecting the head

250 E

The Vision 250 E is supplied with an unwired male 24-pin Fischer connector, which should be

configured to suit the installation. Encoder pin designations are listed in

Table 2.1

250 IT

The Vision 250 IT is connected to the IT interface box by a bifurcated cable, with a male 24-pin Fischer

connector for the pan and tilt encoders and a D-type connector for the lens encoders. Pin designations are
listed in

Table 2.3

The IT interface box is connected to the virtual studio system by either a RS-232 or RS-422 interfaces

using D-type connectors. Pin designations are listed in

Table 2.2

NOTE:

Jumpers in the IT interface box must be set to suit either a RS-232 or RS-422 interface.

Table 2.1 250 E Encoder Pin Designations

Encoder

Connector

Encoder Wire

Colour

Connector Pin

No.

Encoder

Connector

Encoder Wire

Colour

Connector Pin

No.

Pan A1

Black

Tilt A1

Black

Pan A2

Brown

Tilt A2

Brown

Pan A3

Red

Tilt A3

Red

Pan A4

Orange

Tilt A4

Orange

Pan A5

Yellow

Tilt A5

Yellow

Pan A6

Green

Tilt A6

Green

Pan B1

Blue

Tilt B1

Blue

Pan B2

Violet

Tilt B2

Violet

Pan B3

Grey

Tilt B3

Grey

Pan B4

White

Tilt B4

White

Pan B5

Pink

Tilt B5

Pink

Pan B6

Cyan

Tilt B6

Cyan

Table 2.2 250 IT RS Interface Connectors

RS-232

RS-422

Function

Wire Colour

Connector Pin

No.

Function

Wire Colour

Connector Pin

No.

Red

TX-

Brown

Orange

RX-

Black

Gnd

Black

TX+

Violet

RX+

Green

Summary of Contents for Vision 250 IT








































































Search results

Summary of Contents for Vision 250 IT

Reviews:

Related manuals for Vision 250 IT

Brands by name

Popular brands

Vinten Vision 250 IT, Maintenance Manual

Search results

Summary of Contents for Vision 250 IT

Reviews:

Related manuals for Vision 250 IT

Brands by name

Popular brands