- Do not stack more than 1.5 rows of standard
0.75L bottles per shelves to facilitate air circulation.
- Avoid obstructing the internal fans (Located inside
on the back panel of the Wine Cellar ).
- Do not slide the shelves outwards beyond the fixed
position to prevent the bottles from falling.
- Do not pull out more than one loaded shelf at a time
as this may cause the Wine Cellar to tilt forward.
- Do not cover the wooden shelves with alloy foil or
other materials, as it will obstruct air circulation.
- Do not move your Wine Cellar while it is loaded with
wines.This might distort the body of the Wine Cellar
- Do not cover the wooden shelves with alloy foil or
other materials, as it will obstruct air circulation.
- Do not move your Wine Cellar while it is loaded
with wines. This might distort the body of the Wine
Cellar and cause back injury.
TYPES OF REGULATION
Please note that depending on the loading and
settings chosen it takes about 24 hours for the Wine
Cellar to see the temperature stabilising. During this
time the LED seems to move erratically in particular
for dual zone models. It is normal and this process
occurs whenever the setting is modified and/or
whenever a large amount of bottles are added to the
cellar.Designed to store and mature all wines: red,
white and sparkling. These Wine Cellar reproduce the
ideal conditions for wine storage, at a constant
recommended temperature of 12
℃
. They can also
be set to provide ideal serving temperature for full
enjoyment of the wine’s qualities. Unless stated by
the wine maker on the bottle, VINTEC recommends
7
℃
for your champagne, 12
℃
for whites and 18
℃
for reds. (Refer to Wine Service Temperature
recommendation chart).
Designed to store wines at the correct temperature
for best enjoyment. The upper chamber can hold 12,
14 or 16 bottles, depending on the models, at a
temperature of 6
℃
to 10
℃
dedicated mainly to
white, sparkling wines and champagnes. The lower
chamber accommodates 20, 30 or 34 bottles
depending on the models, mainly for red wines,
which could be stored either at room emperature
5
User Manual
and and cause back injury.
Factory preset chart
have enough bottles to fill your Wine Cellar , it is better
to distribute the load throughout the Wine Cellar so
as to avoid all on top or all below type loads.
- Do remove or relocate adjustable wooden shelves to
accommodate larger type of bottles or increase the
capacity of the cellar by stacking the bottles up when
necessary. (See removing shelves).
- Keep smalls gap between the walls and the bottles to
allow air circulation. Like an underground cellar air
circulation is important to prevent mould and for a
better homogeneous temperature within the cellar.
- Do not over load your Wine Cellar to facilitate air
circulation.
(18
℃
-20
℃
) for consumption or at 12
℃
for a
longer time of storage.
TEMPERATURE SETTINGS
Important: The LCD displays by default the actual
internal air temperature.
The temperature settings are pre-set at the factory as
follows. In the event of a power interruption, all previous
temperature settings are automatically erased and it will
revert to the preset temperature settings.
It is important to understand that there is a difference
between the air temperature inside the Wine Cellar
and the actual temperature of the wine: You will need
to wait approximately 12 hours before noticing the
effects of temperature
adjustment due to the critical
mass within a full Wine Cellar.
Once the temperature is set, it is strongly advised not to
toy with it or adjust frequently. The thermostat will
maintain the temperature inside the Wine Cellar within
a +/- 2.5
℃
range.
But the thermal inertia of the wine and the glass is such
that within this temperature range, the actual
temperature of the wine will only fluctuate 0.5
℃
to 1
℃
.
Control panel of VWS121SCA-X/VWS165SCA-X/
VWS121SSA-X/VWS165SSA-X
To modify the pre-set temperature of these models
Adjust the desired cooling temperature by pressing the
UP or DOWN buttons. Each depression of the buttons
will scroll through the available temperature settings
in increase or decrease of 1 degree Celsius.
DISPLAY
To shows the temperature of the internal cabinet.
TEMP.SET
To shows the setting temperature.
You can set the temperature as you desire by pushing
the UP or DOWN button. When you push the two
buttons for the first time, the LED readout will show the
original temperature set at previous time.
The temperature setting can be adjusted from 6
℃
to 18
℃.
Model
VWS121SCA-X
VWS165SCA-X
VWS121SSA-X
VWS165SSA-X
Setting
Temperature
12
℃
12
℃
(+/-2.5
℃
)
VWD154SSA-X Upper compartment: 6
℃
Lower compartment: 12
℃
6
℃
(+/-2.5
℃
)
12
℃
(+/-2.5
℃
)
STORAGE & OPERATION