Vintage Air 1967-68 CAMARO w/o Factory Air Gen IV Manual Download | Manualshive

Page: 2 / 18

background image

2

www.vintageair.com

905168 REV G 4/13/15, PG 2 OF 17

Table of Contents

Cover.................................................................................................................................
Table of Contents.................................................................................................................
Packing List/Parts Disclaimer...................................................................................................
Removing OEM Control Panel, Placard Installation...................................................................
Placard Installation (Cont.)...................................................................................................
Cable Converter Assembly Modification, Cable Converter Assembly Mounting Clamp Installation....
Dash/Floor/Defrost Cable Converter Assembly Installation........................................................
Dash/Floor/Defrost Control Harness.......................................................................................
Cold/Hot Cable Converter Assembly Installation, Cold/Hot Control Harness.................................
Cold/Hot Control Harness (Cont.), Off/Hi Cable Converter Assembly Installation........................
Off/Hi Control Harness.......................................................................................................
Final Steps.......................................................................................................................
Control Panel Calibration Procedure.....................................................................................
Control Panel Calibration Procedure (Cont.)..........................................................................
Wiring Diagram..................................................................................................................
Operation of Controls.........................................................................................................
Packing List......................................................................................................................

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17

Thank you for purchasing this control panel kit from Vintage Air. When installing these

components as part of a complete SureFit™ system, Vintage Air recommends working

from front to back on the vehicle, installing the condenser kit, hose kit, and compressor

first, followed by the wiring, evaporator, and finally the control panel.

«
1
2
3
4
...
»

Summary of Contents for 1967-68 CAMARO w/o Factory Air Gen IV



















Reviews:

No comments

Related manuals for 1967-68 CAMARO w/o Factory Air Gen IV

CRD 2 00-1000S Series

Brand: Symbol Pages: 16

Brand: KaVo Pages: 10

Brand: Panasonic Pages: 116

Toughbook CF-T7BWATAAM

Brand: Panasonic Pages: 12

Brand: Dacor Pages: 4

Brand: Nacon Pages: 12

ThermoSensor Clamp

Brand: LaserLiner Pages: 44

Brand: Oki Pages: 20

Brand: Omron Pages: 16

Brand: ICON Pages: 2

Power commander GSXR750

Brand: Dynojet Pages: 4

Brand: Mamiya Pages: 6

Gasoline/Electric DS Golf Car 1996

Brand: Club Car Pages: 48

Brand: Toro Pages: 8

Brand: Valor Pages: 3

Brand: Avenir Pages: 10

Polly PROGRESS5

Brand: Chicco Pages: 48

Brand: Dorken Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands