background image

1964 IMPALA 

w/ AC

 

15

    904064 REV A 7/22/08, 1964 IMPALA w/ AC GEN IV EVAP INSTR PG 15 OF 25

REFER TO SEPARATE INSTRUCTIONS INCLUDED  WITH MODIFIED HOSE KIT. 

MODIFIED A/C HOSE KIT

ROUTE A PIECE OF HEATER HOSE FROM THE WATER PUMP TO THE HEATER LINE COMING THROUGH THE FIREWALL
AS SHOWN IN FIGURE 14, BELOW. SECURE USING HOSE CLAMPS.

ROUTE A PIECE OF HEATER HOSE FROM THE INTAKE TO THE HEATER LINE COMING THROUGH THE FIREWALL
AS SHOWN IN FIGURE 14, BELOW. NOTE: INSTALL HEATER CONTROL VALVE IN-LINE 
WITH INTAKE MANIFOLD (PRESSURE SIDE) HEATER HOSE, SECURE USING HOSE CLAMPS AS SHOWN IN FIGURE 14,
BELOW.  

NOTE PROPER FLOW DIRECTION

.

HEATER HOSE & HEATER CONTROL VALVE INSTALLATION

NOTE:

 VINTAGE AIR SYSTEMS REQUIRE (2) 5/8 HOSE NIPPLES (NOT SUPPLIED). ONE 

ONE FOR THE WATER PUMP (SUCTION) - IF REQUIRED REMOVE EXISTING HOSE NIPPLE OR NIPPLES AND INSTALL 
NEW 5/8 HOSE NIPPLES IN INTAKE AND WATER PUMP. 

FOR THE INTAKE (PRESSURE) AND 

ECU

MODULE

PRESS 

TAPE

#10 SUCTION

LINE (INSULATED)

091671

EXPANSION

VALVE

O-RING 

FROM HTR 

CNTRL VLV

#6 LIQUID

LINE

091061

#10 SUCTION

HOSE

096059

HEATER 

HOSE

FLOW 

FROM 

INTAKE

TO 

WATER PUMP

PRESS TAPE

FIGURE 14

NOTE: HEATER CONTROL VALVE WILL GET HOT TO THE TOUCH WHEN ENERGIZED

Summary of Contents for 1964 CHEVY IMPALA GEN IV w/ FACTORY AIR


























Reviews: