manualshive.com logo in svg

Vincent Associates UNIBLITZ VMM-T1, User Manual, Page: 14 / 43

Share
Download
Vincent Associates UNIBLITZ VMM-T1 User Manual Download Page 14

 

VMM-T1 User Manual 

 

14 

time-lag. Check this fuse for failure.  Please refer to the SHUTTER FUSE REPLACEMENT 
section of this manual. 

10.

 

Be advised, a visual inspection of a fuse is usually NOT an adequate test to determine if a fuse 
has failed.  Use a DMM (Digital Multi-Meter) or equivalent test device to determine fuse 
continuity.  

11.

 

Additionally, please note that particular shutter units respond to different minimum pulse widths.  
For example, a standard VS25 shutter has a minimum exposure pulse of 6 msec.  If the timing is 
set for an exposure pulse width less than 6 msec, the shutter may not open fully.  

12.

 

If the unit still does not operate properly, turn off and disconnect the unit.  Please notify Vincent 
Associates immediately.  There are no user-serviceable parts outside or inside of the unit. 

 

CAUTION 

Turn off the unit and remove the plug from the AC source before 
checking for blown fuses

  

Summary of Contents for UNIBLITZ VMM-T1












































Reviews:

No comments