Description
Wall-mounted Tab monitor for Due Fili Plus system with 4.3 in
LCD colour display, handset, loudspeaker for calls, capacitive
keypad for interphone functions: lock opening, self-start, auxil-
iary services, intercom calls and volume, brightness and contrast
control.
It is possible to differentiate the call chimes. The visual signals
are for “door/gate open,” “missed calls,” “user away” and “chime
muting.”
Desktop installation is possible with the desktop base acces-
sory 753A and the interconnecting stud 753B (sold separately).
Wall mountable also on 8-module back boxes (Vimar V71318,
V71718) with mounting frame 753S (sold separately).
*
Article 7548 can be used by people wearing hearing aids.
Technical characteristics
• Surface-wall mount or box installation. Can be fitted to the
wall with plugs or a 3 modules (Vimar V71303, V71703) or
circular 60 mm flush-mounting box (Vimar V71701).
• LCD 4.3 in 16:9 display, resolution 480x272 pixels
• Minimum signal level on the bus in reception: -20 dBm
• Capacitive touch keypad with backlit symbols.
• Power supply for terminals 1, 2 (28 Vdc).
• Absorption:
- on standby: 10mA
- maximum conversation current: 180mA
- peak current limited to call time: 180mA
• Ambient class: Class A1 (indoor use)
• Protection class: IP30
• Operating temperature: -5° to 40°C
• Operating ambient humidity 10 - 80% (non-condensing)
• Electronic chimes with different tunes (10).
• Input for landing call.
• Dimensions: 160x180x45,4 mm
• DIP switch for line impedance termination.
Audio frequency function for hearing aids
Art. 7548 can be used by people wearing hearing aids.
However, for correct operation of the hearing aid refer to its
instruction manual. Any metal objects or electronic equipment
nearby may compromise the quality of the sound received by
the hearing aid.
Installation
Important
: We recommend installing the device approximately
160 cm above the floor, making sure it is not exposed to direct
light, so as to avoid bothersome reflections on the surface of the
LCD screen.
Note
: Fig. 1 shows the recommended installation distances, un-
less otherwise specified by current regulations.
1. Secure the plate to the wall with plugs or on a box 3 mod-
ules (Vimar V71303, V71703) or a circular mounting box size
60mm (Vimar V71701).
2. Wire the terminal block (Fig. 6).
3. Terminate the video signal (Fig. 5)
4. Install the monitor as follows: position the monitor on the cou-
The instruction manual is downloadable from the site
www.
vimar.com
pling plate keeping it slightly raised. While keeping the face
plate pressed, apply a light downward pressure until it clicks
into place.
5. Should you need to remove the monitor you need to apply a
light pressure on the lever (Fig. 3) and raise it (from the bot-
tom upwards) so as to release the monitor from the chassis.
Maintenance
Clean using a soft cloth. Do not pour water onto the appliance
and do not use any type of chemical product.
Swiping your palm over the keyboard locks the buttons and all
the LEDs will blink for 5 seconds. The 5s timeout is renewed
every time a button is touched. After the 5s timeout the monitor
will emit another warning beep.
Warnings for the user
Do not open or tamper with the appliance.
In the event of trouble, call in specialized personnel.
Installation rules
Installation should be carried out by qualified personnel in
compliance with the current regulations regarding the installation
of electrical equipment in the country where the products are
installed.
Conformity
EMC directive
Standards EN 60065, EN 61000-6-1, EN 61000-6-3 and EN
60118-4.
WEEE - Information for users
If the crossed-out bin symbol appears on the equipment
or packaging, this means the product must not be
included with other general waste at the end of its
working life. The user must take the worn product to a sorted
waste center, or return it to the retailer when purchasing a new
one. Products for disposal can be consigned free of charge
(without any new purchase obligation) to retailers with a sales
area of at least 400m
2
, if they measure less than 25cm. An
efficient sorted waste collection for the environmentally friendly
disposal of the used device, or its subsequent recycling, helps
avoid the potential negative effects on the environment and
people’s health, and encourages the re-use and/or recycling of
the construction materials.
This product was developed using FreeRTOS
TM
software -
http://www.freertos.org/
3
TAB: 7548
EN