IoT Gateway for connection to the Vimar
Cloud of an IP video door entry system. Once
the necessary licences have been installed,
it provides the video door entry service up to
a maximum of 100 virtual apartments. Up to 5
instances of APP can be associated with each
apartment. Installation on DIN rail (60715 TH35),
occupies 4 modules size 17.5 mm.
Features
• Power supply: 12-30 Vdc SELV
• Consumption:
- 300 mA max at 12 V d.c.
- 140 mA max at 30 V d.c.
• Max. dissipated power: 4 W
• Connection to the respective LAN networks via RJ45 socket
outlet (10/100 Mbps)
• With 4 backlit control buttons
• Operating temperature: - 5 +40 °C (indoor use)
• Operating ambient humidity 10 - 80% (non-condensing)
• IP30 degree of protection
Connections
• Terminals:
- power supply 12 - 30 V d.c. SELV
• RJ45 1 socket outlet for connection to the router providing the
Internet connection (ETH1)
• RJ45 2 socket outlet for connection to IP video entryphone
network (ETH2)
• Port for micro SD card (not used)
Gateway 40165 allows communication between the IP video
door entry system network and the Vimar Cloud. This makes
it possible to manage the IP video door entry system remotely
using the dedicated management portal.
Operation
Gateway 40165 diversifies its functions according to the type of
user (installer, plant manager or end user).
Gateway 40165 requires an efficient band of approximately 2.5
Mbps (in upload) for each video door entry call. Consequently,
the band required is 2.5 Mbps multiplied by the maximum
number of simultaneous calls that the system needs to
support. This number cannot in any case exceed the value of 5
simultaneous calls per gateway.
No specific network configuration is required, provided that:
• ETH1 and ETH2 are configured on separate LANs and do not
overlap
• In the presence of a firewall, make sure traffic is permitted on
the following ports:
- TCP 443, 7042, 8884
- UDP 123, 3478 and from 20000 to 50000
Installer
With Video Door IP Manager:
1. configures gateway 40165 locally connected to the video
door entry system LAN.
2. loads the licences necessary for use.
With the management portal:
3. utilises the connectivity services offered by gateway 40165
operating on the system remotely (contacts list management,
actuations, access control).
Plant Manager
With the management portal:
1. utilises the connectivity services offered by gateway 40165
operating on the system remotely (contacts list management,
actuations, access control, sending users messages).
User
With the management portal:
1. utilises the connectivity services offered by gateway 40165
operating on the system remotely (changing the apartment
name visible on the entrance panel).
With the Video Door APP:
2. receives the video door entry calls from outdoor stations or
control units.
Functions available from the APP or management
portal
Functions available via APP:
• Outdoor unit self-starting.
• Outdoor unit lock opening.
• Video door entry calls from outdoor stations/ and/or control
units to the APPs.
• Activating system actuations (stair light, auxiliary functions).
• Viewing of system CCTV.
• Intercom function not envisaged
Functions available from the management portal:
• System contacts list management.
• Access control management.
• Management of CCTV visibility rights from apartments.
Key functions
F1
: (only on master gateway): Forces synchronisation with
management portal (press for at least 1s).
F2
: (only if ETH1 is configured in DHCP mode): sends request
to the DHCP server for a new IP address for the ETH1
interface.
F3
: no function.
F4
: no function.
LED indications
F1
(cloud connection state):
• permanently on: cloud connected;
• flashing: cloud connection problems;
• 3 rapid blinks after the button is pressed to indicate
synchronisation with cloud has begun.
F2
(ETH1 connection state):
• on: connection active and running;
• off: no Ethernet connection (cable disconnected).
F3
(ETH2 connection state):
• on: connection active and running;
• off: no Ethernet connection (cable disconnected).
F4
(operational state):
• short blink (250ms ON, 750ms OFF): gateway not
configured;
• long blink (750ms ON, 250ms OFF): gateway configured
but not operational;
• double 200ms blink every 2s: gateway operational, only
on master gateway;
• off: gateway operational, only on slave gateway.
Installation rules
• Installation must be carried out by qualified persons in
compliance with the current regulations regarding the
installation of electrical equipment in the country where the
products are installed.
• The gateway 40165 must be installed inside the electrical
panels and must therefore be housed in the containers with
DIN rail support.
• The gateway 40165 can be powered by:
- Power supply 01831.1 (output 12V).
- Power supply 01400 or 01401 (via output 29V “AUX”).
• Maximum power cable length: 10 m (from power supply to
gateway 40165).
• Power cable section: 2x0.5 mm
2
up to 2x1.0 mm
2
.
• The ethernet line must be wired with a UTP (non-shielded)
cable, CAT.5e or superior.
• Maximum Ethernet cable length: 100 m.
• The gateway 40165 must be wired to the IP video door entry
system (via the ETH2 interface) according to the rules adopted
for a standard IP video door entry system.
• All electrical interfaces on the device are SELV. The device
must therefore be installed in high-voltage-free SELV electrical
panels; if present, the installer must guarantee double
insulation between the high voltage and the SELV.
• In the event of access to mini/micro USB, micro SD ports
and reset button (SELV interfaces), comply with the measures
required to prevent electrostatic discharge from the user,
which could damage the device.
WARNING: Update the firmware to the latest version!
Regulatory compliance
EMC directive. RoHS directive.
Standards EN IEC 62368-1, EN 55032, EN 55035, EN IEC
63000.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product
may contain traces of lead.
FCC (United States) Regulatory Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
This device complies with FCC radiation exposure limits set
forth for an uncontrolled environment.
Responsible Party – U.S. Contact Information:
VIOLETTE
ENGINEERING
CORPORATION
https://violetteengineering.com/
WEEE - Information for users
If the crossed-out bin symbol appears on the equipment
or packaging, this means the product must not be
included with other general waste at the end of its
working life. The user must take the worn product to a sorted
waste center, or return it to the retailer when purchasing a new
one. Products for disposal can be consigned free of charge
(without any new purchase obligation) to retailers with a sales
area of at least 400 m2, if they measure less than 25 cm. An
efficient sorted waste collection for the environmentally friendly
disposal of the used device, or its subsequent recycling, helps
avoid the potential negative effects on the environment and
people’s health, and encourages the re-use and/or recycling of
the construction materials.
Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
40165
49401761A0 03 2203
