background image

Figure 4 The arch installation

Assemble each arch on ground. Each arches

consist of:
One Top roof tube (Part #1)
Two Roof curving tube (Part # 2/2A/2B)
Two Sidewall tube (Part # 3/3A/3B/3C)

Connect the arches by Using the hexagon

bolts with washers and nuts through predrilled
holes in frame members. Do not tighten down
the nuts completely until frame is fully

assembled and set in place.

Step #2 --ARCH ASSEMBLY

THE FRONT AND BACK PANEL
FRAME ASSEMBLY

Assemble the front and back panel frame.
According to Figure 5&6, connect the end
wall frame by Using the bolts with washers

and nuts through predrilled holes in frame

members. Do not tighten down the nuts

completely until frame is fully assembled and
set in place.

Figure 6 Frame Installation
for Back Panel

NOTE: Please notice that the part code of the

arch sections. The sections of different arches
are not the same.  Check with the Part List and

the Sketch Figure #1.

NOTE: The Arches, the Front and Back panel

should be assembled well on the ground, before
erected into the Base Flanges.

1

2/2A/2B

3/3A/3B/3C

Figure 5 Frame Installation
for Front Panel

10

11

12

12A

13

13A

3C

2A

1

3A

1

2B

3B

16

17

14

15

Summary of Contents for JIT-2326J















Reviews: