background image

Congratulations

 

on your purchase of our instant shelter. This unit is a combination 

of excellent manufacturing and design. It is comprised of a rigid frame and a durable 
cover.  For  easy  assembly,we  have  marked  all  the  parts  with  codes.  With  proper 
installation,use  and  maintenance,your  unit  will  provide  mang  years  of  good  and 
suitable service. 

 

READ ALL THE INSTRUCTIONS BEFORE ASSEMBLY ! 

 

1.The proper erection and installation of this building requires a high level of care and 
safety. We recommend the safety regulations be complied with during the installation. 
It includes but is not limited to: 
        - Safety hats, protective eyewear and protective clothing 
        - Safety harnesses for all elevated workers 
        - Proper ladder, cage, and safety operation 
2.  Site  selection:  Choose  a  solid  level  location  for  your  building.  Do  not  install  the 
building  where  the  ground  could  not  keep  the  building  steady.  Do  not  install  the 
building where the ground could not bear the weight of the building. Do not install the 
building in soft grass ground or wetland. 
3.  Be  cautions  with  the  surroundings.  Keep  work  area  clean.  Do  not  set  up  it  near 
snow  drifts,  n  slippery  places,  or  in  wet  location,  The  cover  of  the  building  will 
protect  against  normal  falling  leaves  and  light  debris,  however,  large,  fast  or  sharp 
falling  items  etc.  may  cause  a  puncture  or  tear  in  the  cover  material.  So  keep  the 
building away from such harmful things. Be careful with power and heat sources. Do 
not keep heat sources near the tarpaulin. Do not expose to open flame. 
4.  Chose  a  windless  day  to  install  the  building.  It  is  very  difficult  to  attach  the  in 
heavy wind. 
5. All snow accumulation on the main cover should be removed as soon as possible. 
Otherwise, when old snow on the roof becomes hard with new snow falling in,it will 
increase the burden of the roof badly and will damage the roof. 
6. Try to keep the building, especially  its base,  in a dry condition. This will  help the 
building to have a longer life than keeping it in a wet conditions. 
7. The user should be responsible for the parts missing or damage occurred during the 
installation. 
8. Do not make alteration of the frame. Do not hang anything besides  included parts 
to  the  frame.  Damages,  consequential  damages,  or  injuries  caused  by  improper 
installation, alteration, improper use, or damages caused by snow, wind, or any acts of 
nature  are  owing  to  the  user.  The  building  is  not  intended  for  occupancy  for  any 
length of time

 

 

 

 

 

Summary of Contents for JIT-2326J















Reviews: