Viking RDGSU2005BSB Service Manual Download Page 15

To avoid risk of electrical shock, personal injury, or death, disconnect electrical power source to unit, unless test 

procedures require power to be connected. Shut-off gas valve supplying gas to cooktop prior to removal and 

disassembly.

WARNING

!

Disassembly

©2012 Viking Preferred Service

15

Gas valve removal

DANGER

!

Failure to fully engage the gas shut-off prior to the following procedures could result in injury, property 

damage and possibly death.

1.  Disconnect Power from cooktop.
2.  Turn gas supply off going to cooktop, in 

future steps you will be removing gas lines, 

it is imperative that gas supply is turned all 

the way off to prevent gas leaking out.

3.  Remove Stainless steel top, see Page 9 for 

procedure.

4.  Remove Iris spark module, see Page 14.
5.  Disconnect output gas line connection, see 

photo below.

Disconnect line and pull away from 

valve being careful not to damage line 

or valve.

6.  When gas line has been removed, the 

next step is to remove the bolt underneath 

the manifold that secures the valve to the 

manifold.

Remove bolt, making sure 

that rubber seal between bolt 

head and manifold  is retained 

for re-installation

7.  At this time pull gas valve straight up and 

out of manifold, being careful to retain 

the upper seal that goes between the gas 

valve body and manifold, if valve is being 

replaced a new seal will be included with 

the new valve..

Upper seal 

between 

valve and 

manifold

Lower seal 

between 

bolt and 

manifold

Summary of Contents for RDGSU2005BSB




















Reviews: