D. Programming Examples
Programming the RAD-AMP to...
1.
...be in the Line Extender mode
2.
...set the PABX outside line number to 9
3.
...set “Priority 2” access code to 345678
4.
...disable “Priority 1” access code
5.
...set the call timer to 20 minutes
Enter Digits
✱
1
9 #44
345678 #46
#45
40 #48
1. Line Extender Mode
Telecommuting Extender Quick Programming Features
Set the
RAD-AMP
to Line Extender mode (see section
A
) .......................................
Set the
RAD-AMP
to Call Diverter mode (see section
B
) ........................................
Set the
RAD-AMP
to Telecommuting Extender mode .............................................
Security code (6 digits 0-9) (factory set to 845464) ..................................................
Priority 1 access code (enter 6 digits, no digits disables) (factory disabled) .............
“Priority 2” access code (enter 6 digits, no digits disables) (factory disabled) ..........
PABX outside line number (enter 1 digit, no digit disables) (factory set to 9) ............
First remote phone number (1-32 digits each) .........................................................
Second remote phone number (1-32 digits each) ....................................................
Third remote phone number (1-32 digits each) ........................................................
Fourth remote phone number (1-32 digits each) ......................................................
Fifth remote phone number (1-32 digits each) .........................................................
Sixth remote phone number (1-32 digits each) ........................................................
Seventh remote phone number (1-32 digits each) ...................................................
Eighth remote phone number (1-32 digits each) ......................................................
Ninth remote phone number (1-32 digits each) ........................................................
To enter a “
✱
” in the remote phone number ..............................................................
To enter a “#” in the remote phone number ..............................................................
Supervised call forwarding (factory enabled) ...........................................................
Un-supervised call forwarding .................................................................................
To enter a 1 second pause in the remote phone number .........................................
Maximum call timer (enter 2 digits*, no digits disables - factory disabled) .................
Ring delay (1-9) (factory set to 1) .............................................................................
Alert tones On (call progress beeps) (factory enabled) ............................................
Alert tones Off ..........................................................................................................
Enable dial tone detection (for installations without CPC or busy signal) .................
Disable dial tone detection (factory setting) .............................................................
Exit programming and disconnect ...........................................................................
Set all programming features to factory settings ......................................................
* Note:
Call timer digits specified as follows: 00 = 15 seconds, 01-99 = .5 - 49.5 minutes in .5 minute increments.
✱
1
✱
2
✱
3
6 digits
6 digits
6 digits
1 digit
1-32 digits
1-32 digits
1-32 digits
1-32 digits
1-32 digits
1-32 digits
1-32 digits
1-32 digits
1-32 digits
✱ ✱
✱
#
✱
4
✱
7
✱
8
2 digits
1 digit
✱
9
✱
0
✱
5
✱
6
# 7
###
#47
#45
#46
#44
#01
#02
#03
#04
#05
#06
#07
#08
#09
# 48
# 49
Enter Digits
then
then
then
then
then
then
then
then
then
then
then
then
then
then
then
- then - Enter Memory Location
Programming the RAD-AMP to...
1.
...be in the Call Diverter mode
2.
...set the call diverter number to 1-715-386-8861 (up to 32 digits)
3.
...dial 9 (for outside line), pause 1 second, then dial 386-8861
Enter Digits
✱
2
17153868861 #00
9
✱
8 3868861 #00
2. Call Diverter Mode
Programming the RAD-AMP to...
1.
...be in the Telecommuting Extender mode
2.
...set the first remote number to 1-715-386-8861
3.
...set the PABX outside line number to 9
4.
...set “Priority 1” access code to 123456
5.
...clear the “Priority 2” access code
Enter Digits
✱
3
17153868861 #01
9 #44
123456 #45
#46
3. Telecommuting Extender Mode
C. Telecommuting Extender Mode
(Remote Employee)
To access programming in the “Telecommuting Extender” mode, call into the
LINE IN
port. After the
RAD-AMP
answers, enter a
✱
followed by the security code, factory set to V-I-K-I-N-G (
845464
). The
RAD-AMP
will beep twice indicating that programming has
been accessed. It is recommended that the factory security code be changed. While programming, if 20 seconds elapses between
Touch Tones, the
RAD-AMP
will disconnect. All valid Touch Tone programming sequences are acknowledged with a double beep.
A triple beep indicates that a mistake has been made.
Note:
If a “Priority 2” access code is used, program the “PABX outside line
number” with the Touch Tone required to access a C.O. line from a PABX extension.
4
