B. Surface Mounting the PROX-3
The
PROX-3
can be surface mounted to a non-metallic*
wall or post. The unit can be fastened with two screws (pro-
vided) to a single gang electrical box or directly to a wall or
post. For additional mounting strength, the four holes in the
outer corners of the
PROX-3
can be drilled out with an
11/64” drill bit and fastened with four #6 flat head screws.
* Note:
The
PROX-3
can be mounted to a metallic surface
but the proximity card read range will be dropped to
approximately ½ its normal distance.
** Important:
After mounting and testing the card reader,
clean the front recessed area of the unit with rubbing alco-
hol and apply the provided label. Please note, the label is
permanent and not easily removed.
VIKING
©
MODEL
PROX-3
Single Gang
Electrical Box
(not included)
Model PROX-3
** PROX-3 Label
(included)
Optional (4) #6 x 2"
long flathead screws
( not included)
(2) 6-32 x 2" long
phillips screws
(included)
C. Mounting the PROX-3 to a Gooseneck Pedestal Using the PROX-3-MK-GNP Mounting Kit
VIKING
©
MODE
L PRO
X-3
(4) 6-32 x 1.25" long
5/64 hexdrive flathead
screws included with
mounting kit
Model PROX-3
* PROX-3 Label
(included)
1/4-20 Nylock nuts
included with mounting
kit, use with carriage bolts
PROX-3-MK-GNP
Mounting Plate
1/4"-20 x 1" carriage bolts
included with mounting kit
Model VE-GNP Gooseneck Pedestal
(not included) see DOD# 424
Drill out the four holes in the outer corners of the
PROX-3
with an 11/64” drill bit. Attach the
PROX-3-MK-GNP
mounting plate to the
Gooseneck pedestal with the four provided carriage bolts. Wire as shown in section
E
then fasten the unit to the mounting plate with
the 6-32 x 1.25” long flathead screws provided with the
PROX-3-MK-GNP
mounting kit.
* Important:
After mounting and testing the card reader, clean the front recessed area of the unit with rubbing alcohol and apply
the provided label. Please note, the label is permanent and not easily removed.
VIKIN
G
©
MODE
L PRO
X-3
(4) 6-32 x 1.25" long
5/64 hexdrive flathead
screws included with
mounting kit
Model PROX-3
* PROX-3 Label
(included)
1/4-20 Nylock nuts included with
mounting kit, use with carriage bolts
PROX-3-MK-VEGNP
Mounting Kit
1/4"-20 x 1" carriage bolts
included with mounting kit
Model VE-GNP Gooseneck Pedestal
(not included) see DOD# 424
Viking VE-5x5, VE-6x7 or VE-5x10
back box (DOD# 424)
Gasket included
with mounting kit
Gasket included with
model VE-GNP
Channel for routing
PROX-3 wires
Drill out the four holes in the outer corners of the
PROX-3
with an 11/64” drill bit. Adhere the gasket provided with the Viking goose-
neck pedestal, centering on the
VE-GNP
mounting plate. Fasten the
PROX-3
to the mounting plate with the 6-32 x 1.25” long flat-
head screws provided with the
PROX-3-MK-GNP
mounting kit. The
PROX-3-MK-VEGNP
mounting plate can be mounted hoizon-
tally or vertically to allow the
PROX-3
to be postioned on the left, right, top or bottom of the entry phone with a
VE-5x5
or
VE-6x7
surface mount box. The plate can only be mounted on the left, right or top when using a
VE-5x10
surface mount box. Attach the
PROX-3-MK-VEGNP
mounting plate and the
VE-Series
(
VE-5x5
,
VE-6x7
or
VE-5x10
) back box to the gooseneck pedestal with
the four provided carriage bolts. Wire as shown in section
E
. See the entry phone’s Technical Practice for wiring and mounting
instructions.
D. Mounting the PROX-3 and a Viking Entry Phone to a Gooseneck Pedestal Using the
PROX-3-MK-VEGNP Mounting Kit
* Important:
After mounting and testing the card reader,
clean the front recessed area of the unit with rubbing
alcohol and apply the provided label. Please note, the
label is permanent and not easily removed.
