0478 121 9803 A - EN
14
Ensure that the machine is protected from
unauthorised use (e.g. by children).
Thoroughly clean the machine before
storage (e.g. winter break).
Store the machine in good operational
condition.
4.9 Disposal
Ensure that old machines are properly
disposed of. Render the machine
unusable prior to disposal. In order to
prevent accidents, ensure that you remove
the power supply cable or the electric
cable to the motor.
Risk of injury due to the cutting tool!
Always store an old machine in a safe
place prior to scrapping. Ensure that the
machine and the cutting tool are kept out
of the reach of children.
6.
1
Assembling lawn mower
●
Carry out assembly work on
level, flat and solid ground.
Check scope of delivery before
assembly.
●
Assemble the grass catcher box
and install the lower
handlebars (D) – observe the
specified tightening torque.
●
Position the upper handlebar onto the
lower handlebars at the required height
and hold. (
●
Install the upper handlebar and
insert the power cable into the
cable guide (J) as shown and
fasten to the handlebar using the
cable clips (K).
●
Attach the grass catcher box. (
7.
1
Grass catcher box
Attaching:
●
Open the discharge flap (1) and
hold it open.
●
Attach the grass catcher box (2) to the
mountings (3) on the rear of machine by
means of the locating lugs.
●
Close the discharge flap (1).
Detaching:
●
Open the discharge flap (1) and hold it
open.
●
Lift the grass catcher box (2) and
remove it rearwards.
●
Close the discharge flap (1).
5. Description of symbols
Caution!
Read the instruction man-
ual before initial use.
Risk of injury:
Keep other persons out of
the danger area.
Risk of injury!
Beware of the sharp mowing
blade. The mowing blade
runs on for several seconds
after switching off
(motor/blade brake). Before
performing any work on the
cutting tool, before carrying
out maintenance and clean-
ing work, before checking
whether the electric cable is
entwined or damaged, or
before leaving the machine
unattended, switch off the
motor and disconnect the
plug.
Danger of electric shock!
Keep the electric cable
away from the cutting tool.
Switch on the motor.
6. Preparing the machine for
operation
Risk of injury
Observe the safety instructions in
the section "For your safety". (
7. Controls
2
3
4
5
6
Та
ше
в
-
Га
лв
ин
г
ОО
Д
www.tashev-galving.com
Summary of Contents for ME 235
