VIKING
Model:
K-1705-3
261102-1
Serial No:
REN: 1.0B
XXXXXXXX
Viking Electronics, Inc. (715) 386-8861
1531 Industrial St., Hudson, WI 54016
P/N:
DEV:
Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E
RoHS
Back View of the K-1705-3
Yellow (Video)
- Black (GND)
+ Red (6VDC)
** Camera Pwr (+)
Orange
** Camera GND (-)
W/O
Video GND (-)
Green
Video Out (+)
W/G
* Up to 150 ft
3-Wire Gel-Filled Butt
Connectors included
(3M Scotchlok UR2)
CAT5E or
CAT6 Cable
(see Caution below)
Phono (RCA) Plug,
F Connector, Etc.
(+)
(-)
To unused input on TV, VHF
modulator, whole house video
distribution equipment, IP video
encoder (Axis M7001), etc.
Video Out (+)
Video GND (-)
See page 4, section E
Wiring Phone Board
Blue W/BL
W/G Green
W/O
Orange
120V AC
Camera GND (-)
Camera Power (+)
Black with
White Stripe
5V DC Adapter
(included)
Black
(-)
!
(+)
(4) Crimp-on Splice
Connectors (not included)
Phone Board Audio In/Out (Tip)
W/BL
Phone Board Audio In/Out (Ring)
Blue
Green
Red
* Note:
Up to 150 ft video cable run length can be achieved using CAT5E or CAT6 cable. Longer cable runs can be used if a passive or active video Balun transceiver is used on
each end of the cable. Generally, passive transceivers can achieve up to 750 ft cable runs where active transceivers can achieve up to 3000 ft runs depending on cable type, etc.
The type of video balun transceiver required is specific to your cable run length. For more information on video balun transceivers go to: www.northernvideo.com.
Caution:
When routing CAT5E or CAT6 cable, maintain a minimum distance of 3 ft from any parallel high voltage wire (110 VAC) and a minimum of 2 ft from crossing any high volt-
age wire. For installations where RF noise is expected (commercial applications) or wire runs are near high voltage (110 VAC) wires, a shielded video cable such as RG6 is recom-
mended.
D. Adjusting the Camera
The camera can be tilted and rotated to your desired
position. A portable service (test) monitor can be used to
determine the correct viewing angle during installation.
Important:
To prevent the edge of the faceplate from
being viewed in the video image, do not rotate the cam-
era beyond 30 degrees or tilt beyond 20 degrees.
Vertical (Tilt)
Adjustment
+/- 20 degrees
maximum
Horizontal (Rotation)
Adjustment
+/- 30 degrees maximum
Call
VIKING
©
1
2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PRS
8
TUV
9
WXY
0
OPER
#
** Note:
The maximum camera power supply wire run length is 250 ft of 24 gauge wire (CAT 5/6), longer runs are possible by doubling pairs, increasing the wire gauge or using a
6V DC 200mA power adapter (Viking part # L122110). Go to www.vikingelectronics.com and click on “Spare Parts”.
2. Using CAT5E or CAT6 for Video, Camera Power and Phone Board Audio (see Caution below)
*** Note:
RG59 or RG6 with solid center conductor and 95% bare copper braid shield.
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
A. Dip Switch Programming
VIKING
Model:
K-1705-3
261102-1
Serial No:
REN: 1.0B
XXXXXXXX
Viking Electronics, Inc. (715) 386-8861
1531 Industrial St., Hudson, WI 54016
P/N:
DEV:
Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E
RoHS
ON OFF
DIP Switches
(shown
in default positions)
4
3
2
1
8
7
6
5
Rear View of the K-1705-3
5
Switch 1
OFF
ON
OFF
ON
Switch 2
OFF
OFF
ON
ON
Maximum Call Time
Disabled (default)
1 minute
3 minutes
9 minutes
Switch 3
OFF
ON
Disconnect on Dial Tone
Off
On (default)
Switch 7
OFF
ON
Auto Answer Feature
Automatic answer disabled
Automatic answer enabled (default)
Switch 8
OFF
ON
Push Button Feature
Connects calls only
Connects/disconnects calls (default)
Switch 4
OFF
ON
VOX Switching Speed
Fast, 0.2 seconds (default)
Slow, 0.7 seconds
Switch 5
ON
OFF
Switch 6
ON
OFF
Audio Detection
Normal audio detection
Increase audio detect sensitivity for
low level lines. Useful in applications
in which voice or busy signals have
trouble breaking over the speaker.