Viking FGIM515 Installation Manual Download Page 17

17

SERVICE INFORMATION

If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be
obtained from the dealer or distributor in your area.

Have the following information readily available.

• Model number
• Serial number
• Date purchased
• Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency,

 

or if you continue to have service problems, contact Viking Range Corporation at 1-888- (845-4641), or write to:

VIKING RANGE, LLC

PREFERRED SERVICE

1

11 Front Street

Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it if service is ever
required. The model and serial number for your ice machine are located upper
left interior compartment.

Model Number ____________________________________Serial Number ____________________________________________

Date of Purchase ____________________________________________________________________________________________

Date Installed _______________________________________________________________________________________________

Dealer’s Name ______________________________________________________________________________________________

Address ____________________________________________________________________________________________________

If service requires installation of parts, use only authorized parts to insure protection under the warranty.

KEEP THIS MANUAL FOR FUTURE REFERENCE.

Model and
Serial number

Summary of Contents for FGIM515





















Reviews: