background image

1

MODEL

VEDV900

EXTERIOR

BLOWER

10" ROUND DUCT

TO

DOWNDRAFT

WARNING

READ   AND   SAVE   THESE   INSTRUCTIONS

MODEL VDVE900

 

EXTERIOR MOUNTED

 

BLOWER

FOR USE WITH MODELS VDD5300, CVDD5300, VDD5360, CVDD5360, VDD5450, 
CVDD5450, VDD5480, CVDD5480 DOWNDRAFT VENTILATORS.

TO REDUCE THE RISK OF FIRE, ELECTRIC 

SHOCK, OR INJURY TO PERSONS, OBSERVE 

THE FOLLOWING:

1. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the 

manufacturer or your distributor.

2.  Before servicing or cleaning unit, switch power off

at service panel and lock the service disconnect-

ing means to prevent power from being switched 

on accidentally. When the service disconnecting 

means cannot be locked, securely fasten a prom-

inent warning device, such as a tag, to the service 

panel.

3.  Installation work and electrical wiring must be done

by a qualified person(s) in accordance with all ap-

plicable codes and standards, including fire-rated 

construction codes and standards.

4.  Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of 

fuel burning equipment to prevent backdrafting. Fol-

low the heating equipment manufacturer's guideline 

and safety standards such as those published by 

the National Fire Protection Association (NFPA), 

and the American Society for Heating, Refrigeration 

and Air Conditioning Engineers (ASHRAE), and 

the local code authorities.

WARNING

CAUTION

1. For general ventilating use only. Do not use to ex-

haust hazardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, con-

struction dust, etc. off power unit.

3.  Please read specification label on product for further

information and requirements.

4.  Electrical circuit, including speed control, (if used), 

must be rated 6 AMPS minimum.

Blower Dimensions

28.25 x 24.75 x 7.17

PLAN THE
INSTALLATION

1. Locate the blower so the

length of the duct run and

number of elbows needed

are kept to a minimum.

2. Where possible, blower

should be centered between

wall studs or roof rafters.

3. Avoid pipes, wires, or other

ductwork that may be run-

ning through the wall.

ALL INSTALLATIONS

MODEL  VOLTS  AMPS 

CFM 

DUCT SIZE

VDVE900 

120 

5.7 

900 

10 " DIA.

SPECIFICATIONS

5.  When cutting or drilling into wall, or ceiling, do not

damage electrical wiring or other hidden utilities.

6.  Ducted fans must always be vented to the outdoors.
7. To reduce risk of fire, use only metal ductwork.
8. This unit must be grounded.

MODEL VEDV900

EXTERIOR BLOWER

10" ROUND

DUCT

TO

DOWNDRAFT

TYPICAL ROOF MOUNTED INSTALLATION

TYPICAL

WALL MOUNTED INSTALLATION

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

MODEL VDVE900

EXTERIOR BLOWER

MODEL 

VDVE900

EXTERIOR 

BLOWER

Summary of Contents for VDVE900













Reviews: