background image

10

MODEL VG6064

2.     Place gaskets on each side of the side glass

        panel (#10).  Position the bottom hinge on
        the side glass panel as shown.  Screw into
        place with the set screws.

B2

10

7

21

7

GASKETS

10

PLATE

C1

1.

Clean the door glass panel (#14) edge where
the door side seal strip (#5) is to be installed

with rubbing alcohol.  Verify that the soft
flange of the seal strip faces toward the inside

of the shower cabin before seal strip

installation.  Install the seal strip according to

the diagram, making sure the bottom of the
seal is flush with the bottom of the door.

NOTES:

  1.   If the seal strip is not flat or twisted, use
        hot water and a hair dryer to apply
        minimal heat and press the seal strip back
        into position.
  2.   Part #5 is reversible and pre-cut on top
        and bottom to fit in proper configuration.
        Cutting/finishing is needed but only after
        fully installing and only at the top of the
        unit.

C.     INSTALLING THE DOOR PANEL

WARNING

!

DOOR PANEL INSTALLATION REQUIRES

TWO OR MORE PEOPLE TO ASSIST

THIS SIDE MUST

LOOK INSIDE THE
CABIN

5

14

10

16

14

14

THIS SIDE MUST

LOOK INSIDE THE
CABIN

5

VIEW FROM THE TOP

5mm HORIZONTAL
ADJUSTMENT

Summary of Contents for VG6064


























Reviews: