background image

 

MODEL VG06061

 

 

      

 9

 

F.  INSTALLING THE DOOR PANEL 

 

 

WARNING

 

DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST 

 

1.  Clean  the  door  (#13)  glass  surfaces  where  the  hinges  (#8)  are  to  be  installed  with 

rubbing alcohol. 

 

2.  Position the door onto the hinges. Hold securely in place. 

 

3.  Place  a  thin  gasket  (supplied)  on  each  side  of  the  door  between  the  glass  and  hinge 

while holding the door in place. 

 

4.  Install the hinges as illustrated (FIG.8). Use the hex key supplied. 

 

 

G.  INSTALLING THE SIDE & FRONT PANEL SUPPORT 

1.  Install the support assembly (#3) onto the side glass panel (#4) approximately two-thirds 

away from the wall. Use hex key to tighten the screws. [SEE FIG.9] 

 

2.  Install the support assembly to the structural arm (#2) and wall connector (#1).  

 

3.  Mark holes on the wall for the mounting screws. 

 

4.  Remove the support assembly. Drill holes into respective marks and put plastic anchors 

(#19) in them. 

 

5.  Replace  wall  connector  to  proper  position.  Screw  it  in  to  the  wall  with  1-1/8”  screws 

(#16). 

 

6.  Tighten all screws. 

Summary of Contents for VG06061













Reviews: