manualshive.com logo in svg

Vighnaharta TSFC 12-2, User Manual

Share
Download
Vighnaharta TSFC 12-2 User Manual Download Page 23

TSFC 12-2 User Manual 

Vighnaharta Technologies Pvt. Ltd.                                                     Page 

23

 of 

26

                       

 

a.

 

Press 

ENTER 

key  

b.

 

First enter OLD password  

 

 

c.

 

Enter new password and press ENTER to save new password. 

 

 

 

3.1.7

 

Wi-Fi Feature 

This is a unique feature provided by TSFC-12-2 panel for monitoring fire system from anywhere in 

the world using internet and Mobile application. User can monitor Fire panel status on an Android 

or iOS app. If user enables this mode and connects the panel to Wi-Fi, all panel notifications are 
received to user on the mobile application.  

A RESET switch is also available in front panel of Fire panel. It is use to reset the Configuration of 

Wi-Fi setting. 

 

 

 

 

Use 

LEFT 

 and 

RIGHT 

 keys to 

ENABLE/DISABLE

 WIFI function. After 

changing the mode, press 

ENTER

 key to save the changes. 

Old Password 

**** 

New Password 

**** 

WiFi 

   <                DISABLE             > 

Summary of Contents for TSFC 12-2



























Reviews:

No comments

Brands by name

Popular brands

Load more brands