ViewSonic VS11444 Service Manual Download Page 9

Page: 9 / 75

ViewSonic Corporation

Confidential - Do Not Copy

Efficiency (at 115VAC Full Load)

Typical: 80%

Minimum: 75%

Fuse

Internal and not user replaceable

Power Output

35 Watts (typ)

Ripple and Noise

Ripple: <3%

Max Input AC Current

1.2 Arms @ 100VAC, 0.6 Arms @240VAC

Inrush Current (Cold Start)

40 A (max) @ 120VAC

60 A (max) @ 220VAC

Power Supply Cold Start

Shall start and function properly when under full load, with all

combinations of input voltage, input frequency, and operating

temperature.

Power Supply Transient Immunity

Shall be able to withstand an ANSI/IEEE C62.41-1980 6000V 200

ampere ring wave transient test with no damage.

Power Supply Line Surge Immunity

Shall be able to withstand 1.5 times nominal line voltage for one

cycle with no damage.

Power Supply Missing Cycle Immunity

Shall be able to function properly, without reset or visible screen

artifacts, when ½ cycle of AC power is randomly missing at

nominal input.

Power Supply Acoustics

The power supply shall not produce audible noise that would be

detectable by the user. Audible shall defined to be in

compliance with ISO 7779 (DIN EN27779:1991) Noise

measurements of machines acoustics. Power Switch noise shall

not be considered.

Power Saving Operation(Method) VESA

DPMS

Signaling

Power Consumption

Mode LED Power

Consumption

On Green

35 W (Typ)

42 W (max)

Stand By

Amber

< 2 W

Active Off

Off

< 1 W

Recovery Time

On Mode = N/A, Active Off < 3 sec

193

wm-

Summary of Contents for VS11444












































































Search results

Summary of Contents for VS11444

Reviews:

Related manuals for VS11444

Brands by name

Popular brands

ViewSonic VS11444, Service Manual

Search results

Summary of Contents for VS11444

Reviews:

Related manuals for VS11444

Brands by name

Popular brands