ViewSonic VS11444 Service Manual Download Page 48

Page: 48 / 75

ViewSonic Corporation

Confidential - Do Not Copy

6. Troubleshooting Flow Chart

1. Common

Acknowledge

If you change the interface board, be sure that the U103, U105, U106 and U108 these three components also

changed to the new I/F board because there was program inside. If not, please re-write EDID and upload

firmware into U106 via VGA Cable.

If you adjust clock and phase, please do it at the condition of Windows shut down pattern.

If you confirm the R.G.B. color is normal or not, please do it under 16-grey scalar pattern.

This LCM is analog interface. So if the entire screen is an abnormal color that means the problem happen in

the analog circuit part, if only some scale appears abnormal color that stand the problem happen in the digital

circuit part.

If you check the H/V position, please use the crosshatch pattern.

This LCM support more than 30 timing modes, if the input timing mode is out of specification, the picture may

appears abnormally.

If brightness uneven, repairs Inverter circuit or change a new panel.

If you find the vertical line or horizontal line lost on the screen, please change panel.

If you find the speaker don’t working, please don’t plug in audio cable, unless change new speaker.

193

wm-

Summary of Contents for VS11444












































































Search results

Summary of Contents for VS11444

Reviews:

Related manuals for VS11444

Brands by name

Popular brands

ViewSonic VS11444, Service Manual

Search results

Summary of Contents for VS11444

Reviews:

Related manuals for VS11444

Brands by name

Popular brands