background image

Appendix

Safety Guidelines

CAUTION: 

The socket-outlet should be installed near the equipment and be easily accessible.

CAUTION: 

Use a power cable that is properly grounded. Always use the appropriate AC cord that is 

certified for the individual country. Some examples are listed below:

IMPORTANT NOTICE CONCERNING POWER CORD SELECTION

The power cord set for this unit has been enclosed and has been selected according to the country of 
destination and must be used to prevent electric shock. Use the following guidelines if it is necessary to 
replace the original cord set, or if the cord set is not enclosed. 
The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1 
below): 

For the United States and Canada

In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA 
Labeled. For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For 
units which sit on the floor, only SJT type cord sets may be used. The cord set must be selected according 
to the current rating for your unit. Please consult the table below for the selection criteria for power cords 
used in the United States and Canada.

For European Countries

In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is HAR-
Certified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner conductors.

AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM

FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE PLUG SHOULD BE 
CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN 
APPROPRIATE SOCKET.

If a new plug is to be fitted, please observe the wiring code as shown below.

If in any doubt, please consult a qualified electrician.

WARNING:

  THIS APPLIANCE MUST BE EARTHED.

IMPORTANT:

  The wires in this mains lead are coloured in accordance with the following code: 

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

If the coloured wires of the mains lead of this appliance do not correspond with the coloured markings identifying the 
terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by 
the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or 
coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked 
with the letter L or coloured RED.

If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you 
have purchased the product.

USA................. UL
Canada............. CSA
Germany.......... VDE

Switzerland ..... SEV
Britain ............. BASE/BS
Japan ............... Electric Appliance Control Act

Cord Type

Size of Conductors in Cord

Maximum Current Rating of Unit

SJT

18 AWG
16 AWG
14 AWG

10 Amps
12 Amps
12 Amps

SVT

18 AWG
17 AWG

10 Amps
12 Amps

Figure A1

Figure A2

Optiquest        Q71/B-8        15

Summary of Contents for Q71B - Optiquest - 17" CRT Display



















Reviews: