background image

i

Compliance Information

Please read before proceeding

• 

Use only the batteries and power adapter provided by the manufacturer. The use 

of unauthorized accessories may void your warranty.

• 

Do not store your device in temperatures higher than 50°C (122°F).

• 

The operating temperature for this device is from 0°C (32°F) to 35°C (95°F).

FCC Notice

The following statement applies to all products that have received FCC approval. 

Applicable products bear the FCC logo, and/or an FCC ID in the format FCC ID: 

GSS-VS15180 on the product label.This device complies with part 15 of the FCC 

Rules. Operation is subject to the following two conditions: (1) This device may 

not cause harmful interference, and (2) This device must accept any interference 

received, including interference that may cause undesired operation. This 

mobiledevice has been tested and found to comply with the limits for a Class B 

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful interference in a residential 

installation. This equipment generates, uses and can radiate radio frequencyenergy 

and, if not installed and used in accordance with the instructions, may cause 

harmful interferenceto radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause 

harmful interference to radio or television reception, which can be determined 

by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures

• 

Reorient or relocate the receiving antenna.

• 

Increase the separation between the equipment and receiver.

• 

Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected.

• 

Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for 

compliance could void theuser’s authority to operate the equipment.The antenna(s) 

used for this transmitter must not be colocated or operating in conjunction with any 

otherantenna or transmitter.

The device was tested and complies to measurement standards and procedures 

specified in FCC OET Bulletin 65, Supplement C

Summary of Contents for PJ-vTouch-10S




































Reviews: