Viessmann Vitoplex 200 Series Service Instructions Manual Download Page 2

2

Please follow these safety instructions closely to
prevent accidents and material losses.

Safety instructions explained

Danger

This symbol warns against the risk of injury.

!

Please note

This symbol warns against the risk of material
losses and environmental pollution.

Note

Details identified by the word "Note" contain additional
information.

Target group

These instructions are exclusively intended for quali-
fied contractors.

Work on gas installations may only be carried out by
a registered gas fitter.

Work on electrical equipment may only be carried
out by a qualified electrician.

The system must be commissioned by the system
installer or a qualified person authorised by the
installer.

Regulations to be observed

National installation regulations

Statutory regulations for the prevention of accidents

Statutory regulations for environmental protection

Codes of practice of the relevant trade associations

All current safety regulations as defined by DIN, EN,
DVGW, TRGI, TRF, VDE and all locally applicable
standards

a

ÖNORM, EN, ÖVGW G K directives,
ÖVGW-TRF and ÖVE

c

SEV, SUVA, SVGW, SVTI, SWKI, VKF and
EKAS guideline 1942: LPG, part 2

Safety instructions for working on the system

Working on the system

Where gas is used as the fuel, close the main gas
shut-off valve and safeguard it against unintentional
reopening.

Isolate the system from the power supply, e.g. by
removing the separate fuse or by means of a mains
isolator, and check that it is no longer live.

Safeguard the system against reconnection.

Wear suitable personal protective equipment when
carrying out any work.

Danger

Hot surfaces and fluids can lead to burns or
scalding.

Before maintenance and service work, switch
OFF the appliance and let it cool down.

Never touch hot surfaces on the boiler, burner,
flue system or pipework.

!

Please note

Electronic assemblies can be damaged by elec-
trostatic discharge.
Prior to commencing work, touch earthed
objects such as heating or water pipes to dis-
charge static loads.

Repair work

!

Please note

Repairing components that fulfil a safety func-
tion can compromise the safe operation of the
system.
Replace faulty components only with genuine
Viessmann spare parts.

Safety instructions

Safety instructions

5692849

Summary of Contents for Vitoplex 200 Series





































Reviews: