background image

29

Do not carry out 

commissioning

 until the following

conditions are met:

Free passage through the flue gas pipes.

Flue system with positive pressure is gas-tight.

Inspection port covers checked for secure and tight
seating.

Apertures for ensuring sufficient combustion air sup-
ply are open and cannot be closed off.

Applicable regulations on installing and commission-
ing flue systems have been followed.

Danger

Leaking or blocked flue systems or an insuffi-
cient supply of combustion air cause life threat-
ening poisoning due to carbon monoxide in the
flue gas.
Ensure the flue system functions correctly. Aper-
tures for combustion air supply must not be able
to be closed off.
Prevent condensate drainage via a wind protec-
tor.

Connections on the flue gas side

Note
Ensure the flue gas connection is free of load and tor-
que stress.

Flue system installation instructions

Flue gas connection:

7

 200 mm

!

Please note

Balanced or standard flues must not come
loose.
Use floor or wall mounted fixing clamps (bal-
anced flue system accessories) to secure the
pipes in place.

Connect the flue outlet to the flue with the shortest
possible run, maintaining a slight rise (min. 3°). Avoid
sharp kinks.

Commissioning and adjustment

Service instructions for the "Vitocrossal, type
CIB" and boiler control unit

 

Flue gas connection

5839853

 

Summary of Contents for Vitocrossal





































Reviews: