Videx 2301N Kristallo Series User Manual Download Page 30 | Manualshive

Page: 30 / 60

background image

VX2300 2 Wire Video Digital System

PrtCode:VX2300_2_9.doc – Pag.30

08/03/2011

Rev.2.9

Art.318

Two way passive distribution box

BUS

IN

BUS
OUT

BUS

OUT1

BUS

OUT2

Art.318

Close

Open

BL

Fig.1

Fig.2

DESCRIPTION

The unit distributes the bus signal to 2 outputs linked to videophones or intercoms. It is a passive distributor, so there is no possibility to adjust the video
amplification. The device is suitable for small systems with a maximum distance between door panel and the last monitor of 70 metres.

CONNECTION TERMINALS AND JUMPERS
Terminal/Jumper Description
BUS IN

Bus input terminals

BUS OUT

Bus output terminals (to next distrbutor)

BUS OUT 1

Videophone/Intercom bus output 1

BUS OUT 2

Videophone/Intercom bus output 2

BL

Close/Open bus output jumper. If the distributor is the last move to close otherwise leave open.

SPECIFICATION

Housing/Mounting

Plastic box 50x60x20mm / direct wall mounting

Push Buttons

N/A

Programming

N/A

Controls

N/A

Power Supply

Supplied by the BUS line

Working Temperature

-10 +50ºC

CUSTOMER SUPPORT INFORMATION

All Countries Customers

UK Customers

VIDEX Electronics S.p.A.

www.videx.it

–

[email protected]

Tel.+39 0734 631669

Fax +39 0734 632475

VIDEX Security LTD

www.videx-security.com

Tech Line 0191 224 3174

Fax 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution within all
member states of the EU with no restrictions.
This product follows the provisions of the European Directives
89/336/EEC & 92/31/EEC (EMC),
73/23/EEC (LVD) and 93/68/EEC (CE marking).

Il prodotto è marchiato CE a dimostrazione della sua conformità e può essere distribui-
to liberamente all’interno dei paesi membri dell’unione europea EU.
Questo prodotto è conforme alle direttive Europee
89/336/EEC & 92/31/EEC (EMC),
73/23/EEC (LVD) e 93/68/EEC (Marcatura CE).

«
...
28
29
30
31
32
...
»

Summary of Contents for 2301N Kristallo Series





























































Reviews:

No comments

Related manuals for 2301N Kristallo Series

Brand: Bang & Olufsen Pages: 20

Brand: Bang & Olufsen Pages: 24

BeoSound Ouverture

Brand: Bang & Olufsen Pages: 44

Brand: Garz & Fricke Pages: 35

Brand: M-E Pages: 12

Brand: Magnavox Pages: 24

Brand: Magnavox Pages: 22

Brand: Magnavox Pages: 21

Magnavox FW 750C

Brand: Magnavox Pages: 28

Magnavox FW 2012

Brand: Magnavox Pages: 16

MME239 - Micro DVD Home Theater System

Brand: Magnavox Pages: 39

Brand: Yamaha Pages: 83

Brand: Yamaha Pages: 7

Brand: Yamaha Pages: 6

Brand: Yamaha Pages: 14

Brand: Yamaha Pages: 10

Brand: Yamaha Pages: 50

Brand: Yamaha Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands