Videotec DTRX3 Operating Instructions Manual Download Page 5

 

Page 3

MNVCDTRX301_0850 

1 Introduction 

1.1 Contents of the packaging

  1 DTRX3 receiver 
  1 user’s manual 
  2 PG11 blanking caps 
  4 wall mounts with relevant fastening screws 

On  delivery,  please  make  sure  that  the  packaging  does  not  present  damages  or  evident  signs  of  falls  or 
scratches. In case of evident damages, contact immediately the supplier. 
Please, make sure that the contents correspond to the components list mentioned above. 

1.2 Contents of this manual

This manual contains the description of the DTRX3 receiver, with the relevant installation, configuration and use 
procedures.

Before installing and using the receiver 

it is necessary 

to read carefully the present manual

,

in particular the section concerning the safety rules. 

1.3 Typographical conventions

The following section illustrates the meaning of the several graphic symbols used in the present manual: 

 Risk of electric shock; before proceeding with the operations, if not otherwise stated, disconnect the unit. 

  The  operation  is  very  important  for  the  correct  functioning  of  the  system:  please  read  carefully  the 

procedure indicated and carry it out according to the prescribed specifications. 

  Description  of  the  system  features;  we  recommend  reading  carefully  the  sections  marked  with  this 

symbol in order to understand the phases which follow. 

2 Safety rules 

 The DTRX3 receiver complies with the rules in force at the time of publication of the present manual as 

regards the electric safety, the electromagnetic compatibility and the other general requirements. 
Nevertheless  we  would  like  to  assure  the  users  (installer  and  operator)  illustrating  some  measures  to  be 
adopted in order to guarantee the maximum safety: 

  The  installation  of  the  unit  (and  of  the  whole  plant  of  which  this  unit  is  part)  must  be  carried  out  by 

adequately skilled technical personnel 

  The unit must be opened only by  skilled technical personnel.  The warranty limits does not cover  damages 

resulting from an improper use of the unit 

  Connect the unit to a power supply corresponding to the one indicated on the rating plate (see next section 

Operating data on the rating plate

)

  The outlet must be adequately grounded according to the rules in force 
  Before moving or carrying out technical operations on the unit, disconnect it 
  Do not use worn or damaged power cords, since they represent a serious risk for the user’s safety 
  Do not use the device in areas containing inflammable substances 
  Equipment must be opened only by skilled technical personnel in a non explosive atmosphere. The warranty 

limits does not cover damages resulting from an improper use of the unit. 

  Do not allow children or unskilled persons to use the unit 
  Make sure that the unit is fixed securely and firmly 
  The unit is considered off-line only when the power supply is disconnected and the cables aimed to connect 

the unit with other devices have been removed 

  Before feeding the DTRX3 a protection device must be installed in the building electrical network 
  For the after-sales service, please contact exclusively the authorised technical personnel 
  Keep the present manual with care for any future consultation 

Summary of Contents for DTRX3



























Reviews: