background image

(EN) Security notes / (FR) Notes de sécurité / (DE) Hinweise zur Sicherheit

English

Francais

Deutsch

>

 

Remove batteries before any maintenance!

>

 

WARNING, there is a risk of explosion if a        

battery is replaced by an incorrect type!

>

 

Observe polarity when setting up the batteries!

>

 

Do not throw used batteries!  Bring them to your 

installer or a collection point.

>

 

Attention ! Il y a un risque d’explosion si l’une des 

piles utilisées est remplacée par une pile de type 
incorrect !

>

 

Respectez la polarité lors de la mise en place des 

piles !

>

 

Ne jetez pas les piles usagées ! Ramenez-les à 

votre installateur ou à un point de collecte spé-
cialisé.

 

>

 

 Batterien vor jeglichen Wartungsarbeiten 

entfernen!

>

 

Vorsicht, es besteht Explosionsgefahr, wenn eine 

Batterie durch eine Batterie falschen Typs ersetzt 
wird!

>

 

Achten Sie beim Einsetzen der Batterien auf die 

Polung! 

>

 

Entsorgen Sie Batterien nicht im normalen Haush-

altsmüll! Bringen Sie Ihre verbrauchten Batterien zu 
den öffentlichen Sammelstellen.

FCC Regulatory Information for USA and CANADA

FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI VideoTechnologies may void the FCC authorization to operate this equip-
ment.

FCC Part 15.105 Class B 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following measures:

>

 

Reorient or relocate the receiving antenna.

>

 

Increase the separation between the equipment and receiver.

>

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

>

 

Consult the dealer or an experienced radio/TV technician for help.

Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum 
distance of 20 cm between the radiator and your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions:

1

 

This device may not cause harmful interference, and 

2

 

This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la Partie 15 des règlementations de la FCC et avec la norme RSS-210 de l’Industrie Canadienne.

Son fonctionnement est soumis aux deux conditions suivantes :

Cet appareil ne doit pas causer d’interférences nuisibles et 

Cet appareil doit accepter toute interférence reçue, y compris les interférences pouvant entraîner un fonctionnement indésirable.

I N S T A L L A T I O N   S H E E T

Indoor MotionViewer 

IMD 

200/601/701

www.videofied.com

Summary of Contents for IMD 200

Page 1: ... Install the detector and other system devices in the following order Programming RF Testing Program detector and all other devices into the control panel and test RF communication at each intended devicelocationtothecontrolpanel Mounting Mountdetectoratthetestedlocation Mounting Rules Usepropertoolsandhardware Mountindoorsinatemperaturecontrolledenvironment Mountdetector2 1to2 3m 6 9to7 5ft fromt...

Page 2: ...on the keypad until the desired AREA number appears then press YES By default all devices in area 1 will be subject to the entryandexitdelays 11 ThedisplayshowsNAME LOCATION Enter an appropriate device name up to 16 characters The name of the device should describe its intended mounting location or zone PressYES Thedisplaywillshowthedevicenumberandnameforyour verification 12 MounttheIMDonthewall F...

Page 3: ...ce to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving ante...

Page 4: ... Dimensions LxWxD 2 75 x 2 x 1 5in 51 2 x 80 9 x 36 8mm Weight 3 oz 58 g without battery Installation Mounting Mounting Height 2 1 to 2 3m 6 5 to 7 5ft Mounting on Wall On Flat Wall With 2 x Screws In Corner With 2 x Screws Closing of the Casing Closing by clip and screw if required by local legislation Certifications standards 868MHz IMD200 Standards EN60950 1 2006 A11 2009 A1 2010 EN300220 1 V2 ...

Reviews: