background image

3

UNIVERSAL DOOR CONTACT 

CT201 CT601 CT702

INSTALLATION SHEET

Security notes / (FR) Notes de sécurité / (DE) Hinweise zur Sicherheit

Français

•  Retirez les piles avant toute opération de 

maintenance !

•  Attention ! Il y a un risque d'explosion si la batterie 

utilisée est remplacée par un mauvais modèle !

•  Respectez la polarité lors de la mise en place des 

piles !

•  Ne jetez pas les batteries usagées !  

Ramenez-les à votre installateur ou à un point de 
collecte spécialisé.

English

•  Remove the batteries before any  

maintenance !

•  WARNING, there is a risk of explosion if a battery 

is replaced by an improper model !

•  Observe polarity when setting up the batteries!
•  Do not litter the batteries when they are used! 

Dispose of them properly according to Lithium 
Metal requirements

Deutsch

•  Batterien vor jeglichen Wartungsarbeiten 

entfernen!

•  Vorsicht, es besteht Explosionsgefahr, wenn eine 

Batterie durch eine Batterie falschen Models 
ersetzt wird!

•  Achten Sie beim Einsetzen der Batterien auf die 

Polung! 

•  Entsorgen Sie Batterien nicht im normalen 

Haushaltsmüll! Bringen Sie Ihre verbrauchten 
Batterien zu den öffentlichen Sammelstellen.

FCC Regulatory Information for USA and CANADA

FCC Part 15.21 Changes or modifications made to this equipment not expressly approved by RSI Video Technologies may void the FCC authorization 
to operate this equipment.

FCC Part 15.105 Class B 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct 
the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Radio frequency radiation exposure information according 2.1091 / 2.1093 / OET bulletin 65
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and 
operated with minimum distance of 20 cm between the radiator and your body.

Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This device complies with Part 15 of the FCC Rules and with Industry Canada licence-exempt RSS standard(s)
Operation is subject to the following two conditions:

This device may not cause harmful interference, and 

This device must accept any interference received, including interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :

L’appareil ne doit pas produire de brouillage, et 

L’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le 

fonctionnement.

Summary of Contents for CT201

Page 1: ...ake the detector to its intended mounting location and make sure that the LED flashes continuously indicating good communication with the control panel 9 Press YES OK to end the radio range test then press ESC NO 10 The display shows AREA ASSIGNMENT AREA 1 Press either arrow button repeatedly until desired AREA number appears then press YES OK 11 The display shows PERIMETER DEVICE Press YES OK or ...

Page 2: ...e wired input is used installing the magnet is not needed 1 Remove the base from the contact 2 Hold the base against the wall and mark the mounting points 3 Drill 4 Mount the base on the wall 5 If using the wired input connect 2 AWG22 wires from the wired detector to the input terminals 6 Mount the detector on its base and lock with the screw 7 Insert the magnet in its case 8 Use the plastic parts...

Page 3: ...ications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interferencetoradioortelevisionreception whichcanbedeterminedbyturningtheequipmentoffandon theuserisencouragedtotrytocorrect the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the ...

Page 4: ...istance 2 cm axis Y Z 1 2 cm axis X External detection Wired input Max wire length 16m Input type NC or NO recorded during detection test DETECTION PROPERTIES BOX Physical properties Material ABS UL94 V0 Dimensions 79 3 mm x 35 mm x 24 6 mm Weight 32 g without battery Installation Mounting Mounting support Non ferromagnetic surface ex wood Wall mounting 2 screws Box sealing 1 screw Environmental p...

Reviews: