Vidalux Hydro Plus Series Installation And Operating Manual Download Page 2

Live in a hard water area?? Limescale in the kettle and on bathroom fixtures?? Suffering from 
unknown adverse health effects from this polluted drinking water??

If you have a shower and 

any feature

 becomes blocked with limescale and stops working THIS IS 

NOT COVERED BY THE WARRANTY, as in reality it is not the products fault, it's the 

poor quality water it has been subjected to 

GOOD NEWS - Designed in partnership with one of the UK’s largest and most trusted water 
softener manufacturers, this sleek, easy fit model is GUARANTEED to work or your money 
back!! Remove all the limescale in a 1-4 bedroom home and benefit from the following

Better tasting drinking water - Easy to install - Guaranteed to work or your money back
No plumbing or chemicals – Cost as little as £2.00 a year to run and the improved condition of 
the water pipes will reduce your heating bills - Made in the U.K - Trialled and tested Over 10 
years | Used by professionals

VIDALUX CLEAR & BRIGHT WATER SOFTENER

Guaranteed to get rid of limescale

Summary of Contents for Hydro Plus Series




































Reviews: