manualshive.com logo in svg

Victron energy CCGX, Instructions Manual

Share
Download
Victron energy CCGX Instructions Manual Download Page 24

Last update: 2018-08-21 10:10

ccgx:start

https://www.victronenergy.com/live/ccgx:start

https://www.victronenergy.com/live/

Printed on 2018-08-21 11:59

A short explanation: the VE.Bus SOC as determined by the Multi or Quattro will be incorrect in above
situation. As it will not take the discharge and charge currents by those other DC Loads, and also
unmonitored chargers, into account.

2.4.4 Details on VE.Bus SOC

While in bulk, the SOC will not rise above the value as set in VEConfigure3 for the “State of
charge when Bolk finished“ parameter on the General tab; default 85%.

3 DVCC - Distributed Voltage and Current Control

3.1 Introduction and requirements

With DVCC enabled, the Venus-device takes a more central role in the Victron system, improving and
changing system behaviour.

Enabling and disabling DVCC:

Go to Settings → System Setup

Required minimum firmware versions:

Multi/Quattro: 422
CCGX / Venus GX: v2.12
VE.Direct MPPTs: v1.29
VE.Can MPPT Solar Chargers cannot be used: they do not yet support the new control
mechanisms.
Lynx Ion + Shunt: v2.04
Lynx BMS: v1.09

In case of an ESS System, the ESS Assistant needs to be version 164 or later (Released in November
2017).

In case of installing a MultiGrid 48/3000 the firmware needs to be version 424 or later.

Do not use DVCC in cases where these requirements are not met.

Important: Where batteries are connected via CAN-bus, check the relevant page on the 

Battery

Compatibility manual

 to see if enabling DVCC has been tested with your battery-type, and is OK. If

DVCC is not mentioned in notes relating to your battery, do not enable DVCC.

For Gel, AGM, OPzS and other lead batteries, DVCC can be used without any problem. The same is
true for Victron Energy lithium batteries with the VE.Bus BMS, the Lynx Ion + Shunt BMS or the Lynx
Ion BMS. DVCC is the preferred operating mode for Redflow ZBM2/ZCell batteries using the Redflow
CANBus BMS.

Minimum firmware for the Lynx Ion + Shunt

Summary of Contents for CCGX




























Reviews:

No comments

Brands by name

Popular brands

Load more brands