background image

 

 

INSTALLATION 

 

Your layout and particular hazards dictate the placement of fire extinguishers.    NFPA-10 requires that 

hand  portable  extinguishers  with  a  gross  weight  less  than  40  lbs.  be  hung  with  the  top  of  the 

extinguisher

  not  more

  than  5  ft.  (1.53  m)  above  the  floor.    Extinguishers  having  a  gross  weight 

greater than 40 lbs. (18.14 kg) should be installed so that the top of the extinguisher is 

not more 

than 3 

1/2 ft. (1.07m) above the floor. Extinguishers should be mounted in a clean and dry location, accessible 

to possible fire hazards and preferably near an exit. 

Never install the extinguisher in a location where 

a potential hazard would prevent easy access.

     

 

Use the mounting bracket supplied with extinguisher or an approved Victory vehicle bracket if needed. 

Secure to a solid surface using the appropriate fixings for the  surface (not supplied) to firmly hold the 

bracket in place.   

 

The  operational  temperature  range  for  this  extinguisher  is  +40°F  to  +120°F  (+4°C  to  +49°C)  [please 

see  the  nameplate  on  your  extinguisher].    The  extinguisher  should  be  adequately  protected  if 

temperatures outside of this range are anticipated.    Keep the extinguisher clean and free from dirt, ice, 

chemicals,  and  any  contaminants  that  may  interfere  with  its  proper  operation.   

DO  NOT 

FUNCTIONALLY  TEST  THIS  FIRE  EXTINGUISHER

.    (Testing  or  any  use  may  cause  the 

extinguisher to gradually lose pressure over time and make the extinguisher ineffective).    Never throw 

an extinguisher into a fire because rapid heat buildup could cause pressure expansion and exceed the 

limitations of the cylinder.   

 

SERVICE TOOLS 

 

Victory recommend that only  the correct  tools, weighing  scales and pressurizing adaptors  are utilized 

for  service  and  recharge  to  ensure  correct  assembly  and  filling  (See  appendix  B  for  detail).  Victory 

recommended  tightening  torque  values  should  be  followed. 

DO  NOT  OVERTIGHTEN

  or 

CROSS 

THREAD

 any threaded connections.     

 

SAFETY 

 

Victory  recommend  the  appropriate  personal  protective  equipment  (PPE)  is  used  as  described  in  the 

Safety  Data  Sheet  (SDS)  available  on  the  Victory  website.  Observe  instructions  for  disposal  of  any 

agent in accordance with SDS. 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for WM2.5GAL
















Reviews: