background image

 

 

 

VICTORY  CORPORATION  DOES  NOT  SERVICE,  MAINTAIN  OR  RECHARGE  FIRE 

EXTINGUISHERS.    THIS MANUAL IS PUBLISHED AS A GUIDE TO ASSIST QUALIFIED 

SERVICE  PERSONNEL  IN  THE  INSPECTION,  MAINTENANCE  AND  RECHARGE  OF 

VICTORY  FIRE  EXTINGUISHERS  ONLY.    NO  INSTRUCTION  MANUAL  CAN 

ANTICIPATE ALL POSSIBLE MALFUNCTIONS THAT MAY BE ENCOUNTERED IN THE 

SERVICE  OF  FIRE  EXTINGUISHERS.    DUE  TO  THE  POSSIBILITY  THAT  PRIOR 

SERVICE PERFORMED  ON THIS EQUIPMENT  MAY HAVE  BEEN  IMPROPERLY DONE, 

IT  IS  EXTREMELY  IMPORTANT  THAT  ALL  WARNINGS,  CAUTIONS  AND  NOTES  IN 

THIS  MANUAL  BE  CAREFULLY  OBSERVED.    FAILURE  TO  HEED  THESE 

INSTRUCTIONS COULD RESULT IN SERIOUS INJURY.   

   

VICTORY ASSUMES NO LIABILITY FOR SERVICE, MAINTENANCE OR RECHARGE OF 

FIRE EXTINGUISHERS BY PUBLISHING THIS MANUAL.

   

 

 

 

 

 

 

 

 

 

 

 

 

 

REFERENCES IN THIS MANUAL:

                                     

AVAILABLE FROM:

   

 

NFPA 10   

Standard for Portable Fire Extinguishers       

National Fire Protection Association   

                  

2022 Edition                                                   

1 Batterymarch Pk. P.O Box 9101   

                                                                                             

Quincy, MA. 02169-7471   

                                                                                               

www.nfpa.org

   

CGA C-1     

Methods for Hydrostatic     

 

 

 

Compressed Gas Assoc., Inc.           

Testing of Compressed Gas         

 

 

4221 Walney Road., 5th floor   

                     

Cylinders                                             

 

Chantilly, VA. 20151-2923   

                                                                                                 

www.cganet.com

 

CGA C-6     

Standard For Visual Inspection   

of Steel Compressed Gas Cylinders  

 

Victory Fire & Gas Inc.   

1713 Lewis Street, Bay City,   

MI. 48706. Office - 989.322.0856. 

E-Mail: 

[email protected]

,   

http://www.victoryfiregas.com

   

Summary of Contents for WM2.5GAL
















Reviews:

Related manuals for WM2.5GAL