Paste Baits
1. Remove bait cup cover.
2. Place your preferred solid bait in
the bait cup located in the middle
of the trap pedal.
3. Replace bait cup cover.
Tied Baits
1. Tie desired bait to raised Victor® V.
2. Orient bait towards middle of trap
pedal.
1. BAITING TRAPS
3. CONNECTING
4. DOWNLOAD THE APP
1. Plug in the VLINK™ hub.
If you are planning to use your local network, plug
your ethernet cable into the ethernet port.
For all other hub instructions, refer to the online setup
guide at www.vlinkhq.com/instructions.
1. Download the VLINK
™
app from the Apple or Google Play
Store.
2. Launch the app and follow the on-screen instructions to
connect your trap to the app.
5. SET TRAP
1. Once your trap has successfully connected, set it and forget
about it!
2. Place traps indoors or outdoors.
START-UP GUIDE
Victor
®
VLINK
™
Mouse Trap Model: V420 | Victor
®
VLINK
™
Rat Trap Model: V430
FCC:
this device complies with part 15 of the fcc rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this device not expressly approved by Woodstream
Corporation could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
IC:
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause interference; and (2) This device must
accept any interference, including interference that may cause undesired operation of the device.
RF Exposure:
This equipment complies with FCC and IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a minimum
distance of 20cm between the radiator and your body.
WARNING:
Electric Shock and Spark Hazards.
Ignition:
Do not use near unvented flammable
vapors, liquids, or combustible solids. Do not use in barns, stables, or similar wet or dusty
locations.
High Voltage:
Keep out of reach of children and pets. Use only dry hands or rubber
gloves to handle. Power OFF and bait. Do not touch metal plates when device is powered on.
Electromagnetic Waves:
Keep pacemakers and life support devices at least one foot away.
Consult your heart doctor if you receive a shock. Failure to read and heed all warnings and
directions may cause electric shock, fire, or serious injury. Read and follow all label instructions.
Manufactured for:
Woodstream Corporation
69 N. Locust Street, Lititz, PA 17543
•
800-800-1819
Kill-Bar/Antenna
LED
Indicator
Light
Bait Cup
Bait Tie
Down
Easy-Set
Latch
Kill-Bar
Before you start: Confirm you have a VLINK
™
account
and are able to successfully log in at www.vlinkhq.com.
Trap Set
Thumb Grips
Bait Cup
Cover
QR Code
Label
Rodent Grabbing
Teeth
Trap
Mounting Holes
1. Hold the back end of the trap,
placing both thumbs on the
thumb grips.
2. Pull bar back into the easy-set
latch until it clicks and locks.
3. Take notice of LED light
sequences on the back left corner
of the trap.
2. SET TRAP
LED Light Sequences
1. Green Flash When Set: The trap is
set and fully powered.
2. Red Flash When Set: The trap is
set but the battery is low.
3. Blue Flash When Set: The trap is
connected to the gateway.
4. Red Flash When Disengaged:
The trap is in power saving mode.
