manualshive.com logo in svg

Victaulic VAPS224, Operating And Maintenance Instruction Manual

Share
Download
Victaulic VAPS224 Operating And Maintenance Instruction Manual Download Page 12

10

VAPS 224 Pipe Stand

TROUBLESHOOTING

GENERAL

Problem

Possible Cause

Solution

Pipe flare is 
excessive.

Pipe is “over tracking”.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Pipe height adjustment is too 
high.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Roll grooving tool is tilted 
forward.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Pipe face is 
excessively scuffed.

Pipe is “over tracking”.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Pipe will not stay in 
roll grooving tool.

Insufficient pipe tracking 
angle.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Pipe rotating in the wrong 
direction.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Pipe not square cut.

Cut the pipe end squarely. Refer to the 
Operating and Maintenance Instructions 
Manual for the grooving tool.

Pipe is below level.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Roll grooving tool is tilted 
forward.

Refer to the Operating and Maintenance 
Instructions Manual for the grooving tool.

Ball transfers are jammed or 
sticking.

Clean and lubricate the ball transfers.

TM-VAPS224 0149 Rev_B.fm  Page 10  Tuesday, May 31, 2005  8:20 AM

Summary of Contents for VAPS224















Reviews:

No comments

Brands by name

Popular brands

Load more brands