manualshive.com logo in svg

Vicon SVFT-PRS, Installation & Operation Manual

Share
Download
Vicon SVFT-PRS Installation & Operation Manual Download Page 33

XX163-17-00 Rev 1208 SVFT-PRS Pressurized Dome Housing 

Installation  

•

  25 

 

 

 

VOX Silence Period

 – Defines the time between reaching VOX OFF level and the actual audio turns 

off. Default setting is 5000 ms. 
 

 

 
After the SurveyorVFT has been configured for ViconNet, upon another boot up (or preset 97), the opening 
screen will display (see below). This screen displays the camera dome program version, current date/time 
and some of the word ViconNet. Upon completion of homing, the SurveyorVFT is ready to verify proper 
operation. (Note: Screen below is only a sample screen.) The word ViconNet remains on the screen until a 
PTZ action is taken. 

Note: The camera drive always returns to the pan and tilt coordinates it was initially powered-up with unless 

autohome on power-up was set. 

 
 

 

 

 

 

 

 

Opening Screen

 

Function list: 

VOX Off 

Threshold 

Function list: 

VOX Silence 

Period 

Summary of Contents for SVFT-PRS

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands