background image

XX172-15-00 Rev 1010 KTX-4 Digital Video Encoder 

 Important Notice 

  i 

FCC Notice 

Note: Complies with Federal Communications Commission Rules & Regulations Part 15, Subpart B for a 

Class A digital device. 

WARNING 

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in 
strict accordance with the manufacturer’s instruction, may cause interference to radio and television 
reception. It has been type tested and found to comply with the limits for a Class A computing device in 
accordance with the specification in subpart B of part 15 of the FCC rules, which are designed to provide 
reasonable protection against such interference in a commercial installation. However, there is no guarantee 
that interference will not occur in a particular installation. If this equipment does cause interference to radio 
and television reception, which can be determined by turning equipment off and on, the user is encouraged to 
try and correct the interference by one or more of the following measures: 

 

Reorient the receiving antenna. 

 

Relocate the equipment with respect to the receiver. 

 

Relocate the equipment away from the receiver. 

 

Plug the equipment into a different electrical outlet so that the equipment and receiver 
are on different branch circuits. 

If necessary, the user should consult the dealer or an experienced radio/television technician for additional 
suggestions. 

The user may find the following booklet prepared by the Federal Communications Commission helpful: 

“Interference Handbook, Bulletin CIB-2” 

This booklet is available from the U.S. Government Printing Office, Superintendent of Documents, Mailstop 
SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1. 

Warning: Power must be removed from this unit before removing circuit modules or ribbon cables. 

 

Caution: This unit contains circuit cards with integrated circuit devices that can be damaged by static 

discharge. Take all necessary precautions to prevent static discharge 

 

Summary of Contents for KTX-4





































Reviews: