Viavi OneExpert ONX CATV 620 Quick Start Manual Download Page 80

Page: 80 / 130

Testing Profile A

✓

Profile A is key to D3.1 modem communication via an OFDM carrier.
This is where command and control, range, and registration occurs.

✓

In practice, profile A may be assigned lower mixed modulations, like
QAM 64/16, so every D3.1 modem can communicate. Lower modulation
profiles can operate at lower MER/CNR and power levels.

✓

If profile A isn’t locked or has uncorrectable CWE, a modem may roll
back and use only SC QAMs in 3.0 mode.

THINGS TO CHECK:

Lock status:

locked

Uncorrectable CWE

none

Profile A

is boot profile; ALL 3.1 modems

must be able to use profile A

Summary of Contents for OneExpert ONX CATV 620



































































































































Search results

Summary of Contents for OneExpert ONX CATV 620

Reviews:

Related manuals for OneExpert ONX CATV 620

Brands by name

Popular brands

Viavi OneExpert ONX CATV 620, Quick Start Manual

Search results

Summary of Contents for OneExpert ONX CATV 620

Reviews:

Related manuals for OneExpert ONX CATV 620

Brands by name

Popular brands