background image

IMPORTANT SAFETY INSTRUCTIONS:

CAUTION:

 To reduce risk of electrical shock or electrocution:

-  Do not disassemble. Do not attempt repairs or modifications. 

  Refer to qualified service agencies for all service and repairs.

-  Do not use this product in or area where it can fall or be pulled into water or other liquids.

-  Do not reach for this product if it has fallen into liquid.

-  Use this compressor with 12-volt DC systems only.

-  This product should never be left unattended during use.

WARNING:

 To prevent injury:

-  Never allow children to operate this compressor. 

  Close supervision is necessary when this compressor is being used near children.

-  This compressor will become very HOT during and immediately after use. 

  Do not touch any part of this compressor with bare hands, other than the ON/OFF switch 

  during and immediately after use.

-  Do not use this product near flames or explosive materials or where aerosol products 

  are being used.

-  Do not operate this product where oxygen is being administered.

-  Do not pump anything other than atmospheric air.

-  Never use this product while sleepy or drowsy.

-  Do not use any tools or attachments without first determining maximum air pressure for that 

  tool or attachment.

-  Never point any air nozzle or air sprayer toward another person or any part of the body.

-  This air compressor is equipped with an Automatic Reset Thermal Protector, and can    

  automatically restart after the thermal protector resets. Always cut off power source when 

  thermal protector becomes activated.

-  Wear safety glasses or goggles when operating this product.

-  Use only in well ventilated areas.

-   After usage, always release excess pressure from the coil hose by turning On/Off switch to the Off  

  position, disconnect hose from compressor, with the tire inflation gun still connected to the other  

  end of the coil hose, pull trigger on the tire inflation gun to release excess pressure.

USER MANUAL

400P AUTOMATIC PORTABLE COMPRESSOR

Summary of Contents for HEAVYWEIGHT Series









Reviews: