VIA Technologies EPIA-M920 User Manual Download Page 53 | Manualshive

Page: 53 / 93

VIA Technologies EPIA-M920 User Manual Download Page 53

VIA EPIA-M920 User Manual

42

5.

Hardware Installation

5.1.

Installing into a Chassis

The VIA EPIA-M920 can be fitted into any chassis that has mounting holes for compatible with the
standard Mini-ITX mounting hole locations. Additionally, the chassis must meet the minimum height
requirements for specified areas of the board. If a riser card module is being used, the chassis will need to
accommodate the additional space requirements.

5.1.1.

Suggested Minimum Chassis Dimensions

The figure below shows the suggested minimum space requirements that a chassis should have in order to
work well with the VIA EPIA-M920.

Figure 48: Suggested minimum chassis dimensions

Each side of the board should have a buffer zone from the internal wall of the chassis. The side of the
board that accommodates the I/O coastline should have a buffer of 1mm. The side on the opposite end of
the I/O coastline should have a buffer of at least 5mm. The two sides adjacent to the I/O coastline should
have at least a 10mm buffer.

For the side that is close to the PCIe slot, the buffer should be at least 100mm if a riser card will be used.

«
...
51
52
53
54
55
...
»

Summary of Contents for EPIA-M920






























































































Reviews:

No comments