Vetus DEUTZ DT44 Operation Manual Download Page 72

Page: 72 / 88

Engine Lubricating Oil

Only use a recognised brand of oil for lubricating the engine.

Lube oils are differentiated according to their performance and

quality class. In common use are specifications named after API

(American Petroleum Institute) and CCMC (Committee of

Common Market Automobile Constructors).

Approved API Oils

CD, CE, CF and CF4

Approved CCMC Oils

D4, D5

As the viscosity of lube oil is dependent on temperature, the oil

vicosity (SAE grade) should be selected according to the ambi-

ent temperature when the the engine is started.

To avoid oil changes dictated by the seasons we advise one of

the following multi-grade oils.

- SAE 10W40 for temperatures of -25°C up to +30°C

(-13°F up to +86°F)

- SAE 15W40 for temperatures of -20°C up to +35°C

(-4°F up to +95°F)

For example:

Vetus Marine Inboard Motor Oil

Shell Super Diesel T

Gearbox Lubricating Oil

Only use a recognised brand of oil for lubricating the gearbox.

ZF Hurth:
AutomaticTransmission Fluid; type A, Suffix A.

For example

: Vetus Marine Gearbox Oil

Shell Donax T6

Gulf Dextron

model ZF45

(HSW450H2) : 2.0 liter

(3.5 UK pt)

model ZF45A (HSW450A)

: 3.0 liter

(5.3 UK pt)

model ZF63

(HSW630H1) : 3.8 liter

(6.7 UK pt)

model ZF63A (HSW630A)

: 4.0 liter

(7 UK pt)

Other brands of gearboxes:
See supplied owners manual for oil type and quantities.

9 Operating media

Lubricating oil

Summary of Contents for DEUTZ DT44
























































































Search results

Summary of Contents for DEUTZ DT44

Reviews:

Vetus DEUTZ DT44, Operation Manual, Page: 72 / 88

Search results

Summary of Contents for DEUTZ DT44

Reviews: