Vetus DEUTZ DT44 Operation Manual Download Page 38

Page: 38 / 88

4 Maintenance

Checking the V-belts

Every 500 operating hours.

VD00034

VD00010

22 Inspection V-belts

Inspect the belts for wear and tear (fraying

and cracking). Belts which are in poor

condition should be replaced.

Warning!

Check, tension and change belts only with

the engine off. Refit belt guard, if provided.

23 Checking tension V-belt

Check tension of the V-belt by applying

moderate finger and thumb pressure. If

the deflection of the belt is more than 9 -

11 mm (approx. 3/8”), using about 10 kg

(20 lbs) thumb pressure, it should be ten-

sioned.

24 Tensioning V-belt of coolant

and fuel pump

• Loosen bolts (1) and (2).

• Rotate the tension device with the fuel

pump in the direction of the arrow using

a key in (a), square 1/2”, until the ten-

sion of the V-belt is correct.

• Re-tighten bolts (1) and (2).

VD00021

”

Summary of Contents for DEUTZ DT44
























































































Search results

Summary of Contents for DEUTZ DT44

Reviews:

Vetus DEUTZ DT44, Operation Manual, Page: 38 / 88

Search results

Summary of Contents for DEUTZ DT44

Reviews: