Vetek Uniscale 100kg/2g Manual Download Page 1

Page: 1 / 10

anual

model

CAPACITY/GRAdUATIoN

VB2-30-eC

max 30 kg / 10 g

VB2-100-eC

max 100 kg / 10 (50) g

VB2-200-eC

max 200 kg / 20 (100) g

VB2-200-eC-Tm

max 200 kg / 100 g

VB2-200-50-Tm

max 200 kg / 50 g

VB2-30-05

max 30 kg / 5 g

VB2-100-02

UNISCALE 100kg/2g

max 100 kg / 2 g

VB2-100-10

max 100 kg / 10 g

WS-130

max 130 kg / 10 g (special)

VB2-130-10

UNISCALE 130 kg /10 g

130kg/10g max

VB2-200-10

max 200 kg / 20 g

UNISCALE 200kg/5g

max 200 kg / 5 g

UNISCALE 200 kg /50 g

200kg/50g max

oVeRVIeW dIffeReNT RANGeS

Scandinavia’s largest webshop for scales

Hantverksvägen

76493

Vaddo, Sweden

Tel.

+46 (0)176-208920

Web

www.vetek.com

[email protected]

WeIGhINGBloCk VB2 SeRIeS ANd UNISCAle

The Weighingblock is a robust scale. It is designed for portable use. When transported by car between

different working places we recommend using of a protected space or a case for the scale.

This will extend the interval for service.

Extern

matning

9 VDC

Kommunika-

tionsport

Alkaliska

batterier

Kalibrerings-

omkopplare

Normal Kalibrering

PRINT

NET

GROSS

OFF

ZERO

TARE

Manual_VB2_V1

Summary of Contents for Uniscale 100kg/2g











Search results

Summary of Contents for Uniscale 100kg/2g

Reviews:

Related manuals for Uniscale 100kg/2g

Brands by name

Popular brands

Vetek Uniscale 100kg/2g, Manual

Search results

Summary of Contents for Uniscale 100kg/2g

Reviews:

Related manuals for Uniscale 100kg/2g

Brands by name

Popular brands