manualshive.com logo in svg

VETEC V-LINK 671201, User Instructions

Share
Download
VETEC V-LINK 671201 User Instructions Download Page 12

Deacti vate peak hold

5.2 Operati ng multi ple dynamometers in the same area (menu 2)

Acti vate menu 2 on the dynamometer

Selecti ng a channel on the dynamometer

Acti vate menu 2 on the handheld display

Press the ON/OFF butt on.

Press and hold MENU unti l the display shows 1.

Press          to go to 2 (Menu 2).

Select 2 by pressing ENTER.

Press the ON/OFF butt on.

Press and hold MENU unti l the display shows 1.

Press            to go to 2 (Menu 2).

Select 2 by pressing ENTER.

*Repeat the above on another dynamometer and select a diff erent channel.

The display shows the default channel.

The fi rst digit is blinking which means that it can be 

changed using the arrows.

Choose between 99 frequencies.

Select a channel by pressing ENTER.

Press RETURN to go back to weighing.

Menu 2 is used when operati ng multi ple dynamometers with wireless displays in the same area. To 

avoid interference each set of dynamometer and wireless display can be set to operate on its own 

channel. In menu 2 it is possible to choose between 99 diff erent channels.

Press and hold MENU unti l the display shows 1.

Select 1 by pressing ENTER.

The display now shows PE on.

Press          unti l the display shows ·PEoFF.

Press ENTER to turn off  Peak Hold.

Press RETURN to go to default setti  ngs.

*Peak hold will not deacti vate when the dynamometer is turned off .

- 8 -

Summary of Contents for V-LINK 671201

















Reviews:

No comments

Brands by name

Popular brands

Load more brands