background image

Table of Contents

 

 

Rev. 3/4/2019 

  POW-CAR-AR5 MANUAL 

Table of Contents

 

Copyright 2019 Vestil Manufacturing Corp.  

Page 7 of 13 

                                     

 

 

 

Delta Motor Speed Controller: 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

To change the controller parameters, use the buttons on the keypad to select the 

desired settings. See 

Speed controller parameter settings

 table (below). 

a.  PROG/DATA: press the PROG DATA button to initiate program mode. The 

following screen will be displayed: 

 

This screen indicates which parameter number is selected, which in this 

case is parameter 0. Press the up or down arrow button to select the desired 

parameter number (0; 1; 2; 6; or 7). Press the PROG/DATA button again to 

reveal the second set of numbers (on the right side of the dash in the 

“parameter” column of the table below). Use the arrow buttons to select the 

desired number. After completing the desired combination of numbers, press 

the MODE button twice to return to the home screen.  

b.  MODE: press the MODE button to display information about the status of the 

drive. Successively pressing the MODE button displays different information. 

For instance, pressing the MODE button 3 times displays the current 

turntable speed in rpm’s (12rpm displays as “u 12”). 

c.  Arrow keys: press the up or down buttons to scroll through different 

parameters. Press the up or down arrow key quickly to change parameter 

settings in single unit increments. 

d.  The following table indicates the controller settings that are necessary to 

achieve a minimum rotation speed of 3rpm and an upper rotation speed of 

12rpm: 

0- 

 

Speed controller parameter settings:

 

 

Parameter  Description of parameter 

Setting 

Description of setting 

0-03 

Start-up display selection 

d2 

Display the content of user-defined unit 

0-05 

User defined coefficient K 

d0.3 

Scales frequency so display shows approximate 

turntable rpm 

1-02 

Maximum output voltage 

d255 

Sets maximum voltage to motor 

1-07 

Upper bound of frequency 

d65 

Sets maximum rotation speed with speed knob 

turned fully clockwise (~12 rpm) 

1-08 

Lower bound of frequency 

d15 

Sets minimum rotation speed with speed knob 

turned fully counterclockwise (~3 rpm) 

1-09 

Acceleration time 

d10* 

Time to accelerate motor to maximum output 

frequency in seconds 

1-15 

Auto accelerate/decelerate 

d0* 

Allows for linear acceleration of motor 

1-16 

S-curve in acceleration 

d 7 

Determines how smoothly drive accelerates 

2-00 

Source of frequency command 

d 3 

Allows turntable speed to be controlled by knob on 

keypad 

2-01 

Source of operation command 

d 1 

Makes drive turn on external foot switch 

2-02 

Stop method 

d 1 

Allows turntable to coast to stop 

6-02 

Over-current stall prevention limit 

d 150 

Sets maximum motor current as percentage of 

rated output 

6-03 

Over-torque detection mode 

d3 

Detection enabled during acceleration & continues 

until Continuous Output Time Limit 

6-04 

Over-torque detection level 

d 200 

Sets maximum output torque as percentage of 

rated output 

6-05 

Continuous output time limit 

d10 

Determines how long (in seconds) drive runs after 

over-torque detected 

7-00 

Motor rated current 

d 120 

Establishes maximum output current as 

percentage of rated output 

7-01 

Motor no-load current 

d 75 

Sets motor slip compensation 

7-02 

Torque compensation 

d 10 

Sets maximum startup torque 

 

Model 

3rpm 

12rpm 

Parameter 

Setting 

Parameter 

Setting 

POW-CAR-AR5 

1-08 

d20 

1-07 

d65 

 

Summary of Contents for POW-CAR-AR5














Reviews: