Vestil EPT-S-2748-33 Instruction Manual Download Page 3

 

2

 

Preface 

Welcome to use this series of Semi-electric pallet trucks SPT15.

 

In order to ensure your safety and 

to correctly operate the shop crane, please thoroughly read and understand all instructions in the 
Instruction Manual as well as all label instructions before operating it for the first time. Please keep 
the Instruction Manual handy for reference whenever necessary.   

This manual will tell about safety operation, main specifications and maintenance of this pallet 

truck. 

To highlight some instructions, the following icons are used in this manual.   

1. 

 

----

refers to a potential danger; if not avoided, it may cause serious human injury, vehicle 

damage or fire.   

2.

 

 

----

refers to a potential danger; if not avoided, it may cause minor human injury, or local 

damage to the vehicle.   

3. 

----

 Refers to general notes and instructions before use.

 

  Most parts of the product are made from recyclable steel. The recycling and disposal of 

cast-offs resulted during use, maintenance, cleaning and disassembling the product has to comply 

with local regulations without pollution to the environment. The recycling and disposal of the 

cast-offs should only be operated by specialised personnel in the designated area. The cast-offs 

such as hydraulic oil, batteries and electronic units, if improperly disposed, may be hazardous to the 

environment and human health.

 

 

 

Due to continuous product improvement, Noblelift reserves the right to make changes in 

product designs and specifications without prior notice. For the latest product parameters, please 
feel free to contact us. Note: All parameters provided herein are as of the publication date of the 
Instruction Manual.

 

 

 

 

 

 

Summary of Contents for EPT-S-2748-33
























Reviews: