background image

43

40

-8-

RE

FRONT PANEL SECTION

@6

MIX VOLUME

It  is  the  volume  which  adjusts  the  master  output 

level  of  SAMPLER  /  DELAY.    When  you  want  to 

monitor  the  signal  outputted  from  SAMPLER  / 

DELAY  by  headphone,  please  set  this  volume 

minimum. 

@7

EFFECT CUE SWITCH

It  is  the  switch  for  monitor  sound  of  SAMPLER  / 

DELAY  by  headphone.  When  the  switch  is 

pushed, MONITOR SELECT switch is changed to 

a MASTER/EFFECT CUE sides, you can monitor 

of  the  signal  outputted  from  SAMPLER  /  DELAY. 

When a switch is on, EFFECT CUE indicator lights 

up. 

@8

EFFECT CUE INDICATOR

It  is  the  indicator  which  tells  ON/OFF  state  of 

EFFECT  CUE  switch.  The  light  is  up  when  a 

EFFECT CUE switch is on. 

@9

LEVEL/PLAY VOLUME

It  is  the  volume  which  adjusts  the  effect  level  of 

SAMPLER  /  DELAY.    In  the  SAMPLER  mode, 

the  fader  operates  start/stop  of  a  phrase  of 

sampling.    If  volume  is  raised,  it  will  start 

playback with the level according to the scale of 

the volume, and if it is set at minimum, playback 

will stop. 

#0

CURVE SWITCH

It  is  the  switch  which  sets  up  the  volume  curve 

property of LEVEL/PLAY volume.  At the time of 

the "C" side, level of sound increase rapidly. And 

at  the  "A"  side,  the  level  increase  loosely.    It  is 

convenient if you use properly in the right time of 

DELAY mode and SAMPLER mode. 

#1

TAP SWITCH

In  the  DELAY  mode,  switch  works  to  set  up 

delay  time.  And  the  button  blinks  according  to 

the set-up delay time.  In the SAMPLER mode, it 

works  as  a  switch  for  starting.  During  playback, 

the button lights up.

#2

MIC input jack

It is the input jack for MIC. 

#3

MIC EFFECT SWITCH

It is the select switch which sends the signal of a 

MIC  channel  to  built-in  SAMPLER/  DELAY.  If  it 

pushed,  a  signal  will  be  sent  to  SAMPLER  / 

DELAY,  and  MIC  EFFECT  SEND  indicator  will 

light up. 

#4

MIC EFFECT INDICATOR

LED  will  light  up  when  MIC  EFFECT  switch  is 

pushed. 

#5

It  is  the  volume  which  adjusts  the  level  of  the 

microphone connected to MIC input jack. 

#6

It  is  a  jack  only  for  headphone.    Please  use  the 

stereo headphone over impedance 8ohms.

MIN

MAX

LEVEL

EFFECT

MIC IN

MIC

36

32

34

33

35

MIC LEVEL VOLUME

PHONES (headphone) jack

#7

FO

It  i

wo

you

is c

up 

#8

LIN

It is

pla

pla

sup

#9

PH

It  i

tur

add

hea

$0

MA

It is

 (In

con

LIN

$1

GN

It is

turn

hum

turn

PMC05ProSL-E    04.7.13  11:22  AM    ページ 9

Summary of Contents for PMC-05ProSL VCA

















Reviews: