background image

3

Front Panel

Front Panel Explanation

1

Power Switch

The power switch should be in the OFF
position when plugging and unplugging
the power cable.

2

Phones Jack

Plug headphones into this jack to monitor.

3

Phones Volume Knob

Used to adjust the volume sent to the
headphones jack.

4

Reset Button

Used to reset the counter to 00:00. Used
in “relative” mode, not “absolute “ mode.

5

ABS/REL Button

Used to cycle the counter from “relative”
mode to “absolute” mode.  Absolute
cannot be reset or changed. Relative can
be reset and used with SMPTE or MIDI
sync time codes.

6

Counter window

displays time, parametric values, and
operational descriptions, depending on
the mode.

7

A Button

HDR immediately goes to “A” point when
pressed.

8

B Button

HDR immediately goes to “B” point when
pressed.

9

ENTER Button

Used to execute parameter changes.

10

EXIT Button

Used to cancel operations or exit (go
 out from) modes.

11

AB Function

Selects from three actions: AB Single,
which plays back the portion of audio
between your A and B points, AB
Repeat, which loops the audio
between your A and B points, and
AUTO Punch In/Out, where you can
program the HDR to enter Record
mode at your A point and Exit record
mode at your B point.

12

Edit Button

Cycles between three Edit choices
Move, Copy or \Delete.

13

Utility Button

Cycles between three choices: Merge,
MIDI, and Backup/Load Song
Function.

14

Rewind / Past Forward / Stop /
Play / Record Buttons

These transport controls operate the
HDR just like a tape recorder. Rewind
and Fast-Forward have 3 speeds.
Pressed once is normal, pressed

twice

 is faster, and pressed 

three

times

 is very fast.

15

Meter display

Shows the input levels, playback
levels, and  mixer parameter values
for each individual track.

16

Record / Mute Track Select Buttons

In normal mode, pressing one of these
buttons will arm the track for recording
(Red LED lights). If the Mute mode is
selected, pressing one of the buttons
will mute the track selected. (Green
LED will light)

17

Mute Button

Selects Mute mode, for muting tracks
1-8. Must press again to 

de-select

Mute mode.

Summary of Contents for HDR-V8





































Reviews: