VESPA PX 150 USA Workshop Manual Download

Page: 72 / 138

Front

Front wheel hub overhaul

After removing the front brake calliper, remove the

plastic cap shown in the figure.

Remove the pin and the locknut.

It is now possible to remove the wheel axle nut.

After removing the split ring on the outer side of

the wheel hub, and the seal ring, remove the bear-

ing using a length of pipe of adequate diameter

and a mallet, as shown in the figure. Follow the

same procedure to remove the roller cage on the

opposite side.

Handlebar

Removal

Remove the 2 rear view mirrors and their fixing ring

nuts. Remove the handlebar cover as described in

the «Bodywork» chapter and the speedometer.

Suspensions

Vespa PX 150 USA

SUSP - 72

Summary of Contents for PX 150 USA











































































































































Search results

Summary of Contents for PX 150 USA

Reviews:

Related manuals for PX 150 USA

Brands by name

Popular brands

VESPA PX 150 USA, Workshop Manual

Search results

Summary of Contents for PX 150 USA

Reviews:

Related manuals for PX 150 USA

Brands by name

Popular brands